Martin Fireplaces B36RA, B36LA manual Fireplace Operation

Page 26

FIREPLACE OPERATION

WARNING: If a decorative gas appliance is used in the fireplace the fireplace damper must be fixed in an open position. (See additional operation information in section titled “Operation Guidelines”.)

WHICH WOODS ARE BEST?

Each wood species offers something different in aroma or heat value, and you should consider your needs and desires before building your fire.

Softwoods, like pine, spruce, and fir are easy to ignite because they are resinous. However, a fire built entirely of softwoods burns out quickly and requires frequent replenishment. While a softwood fire is not too desirable for a long evening, it’s fine in the morning when you want quick warmth, or late in the evening when you want a fire that will burn out before you go to bed.

On occasion when a longer fire is desired, it’s best to combine softwoods with the heavier hardwoods such as ash, beech, birch, maple, oak and hickory. These hardwood species burn less rapidly, with shorter flames, and produce steady, glowing coals.

For the most pleasing aroma, you’ll want to burn the wood of fruit trees such as apple and cherry, or nut trees such as beech, hickory and pecan. Such wood is generally more expensive, but a little combined with other wood, goes a long way. Start your fire with a mixture of softwood and hardwood, then add some fruit or nut wood for nostalgic aroma. Since most woods will not burn well when freshly cut, the wood you purchase should be reasonably dry. The sizes you buy are dictated by the size of your fireplace. Purchase logs that will fit when laid across your grate, and ask that the larger, heavier logs be split. Kindling should be short, easily split lengths of softwood, lumber yard or mill scraps, or twigs and branches gathered from your yard.

HOW TO BUILD A BETTER FIRE

The first three fires should be of moderate size to allow the fireplace to adjust and the bricks to cure before being subjected to larger fires.

First, make sure your room is well ventilated, your damper open and the flue is unobstructed. Then make sure your wood is dry and seasoned. Unseasoned wood burns poorly and coupled with poor ventilation or an obstructed chimney, leads to smoking problems.

If your fireplace is equipped with an outside combustion air assembly, open its combustion air damper by pushing upward on the lever located above the firebrick on the corresponding side of the firebox.

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR "FRESHEN UP" A FIRE IN THIS FIREPLACE. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE FIREPLACE WHILE IT IS IN USE. USE OF THIS FUEL CAN CAUSE A SERIOUS EXPLOSION.

Prepare your fire by placing two logs on the iron grate or fire basket, and laying the tinder between them. Tinder may be dry scrap paper, twigs, or bark. On top place a small handful of twigs or split softwood kindling. Place more dry logs over this base. Keep logs close together, as narrow air spaces between them promote better drafts, and heat reflected between adjacent surfaces aids in raising and maintaining combustion temperatures.

You’ll need a minimum of three logs, preferably four, to make a good fire. Add kindling and new logs as needed to rekindle a dying fire. New logs should be added at the rear grate after raking the coals toward the front. DO NOT OVERFIRE THE FIREPLACE. Overfire conditions may be created by large amounts of kindling, building scraps, or other improper fuels.

Ashes, important because they form a bed of glowing coals, should only be left to accumulate within an inch or two of the bottom of the grate. Excess ashes can be used to check a flaming fire; or to “bank” your fire, cover the logs with ashes. A “banked” fire will hold glowing coals for 8-10 hours, thereby saving a fire for later use.

26

53D9041. Rev 1 03/03

Image 26
Contents Models B36LA and B36RA Listing and Code Approvals Table of ContentsCongratulations Important Information Operation Guidelines Clearances Fireplace Components Model Number DescriptionFireplace Installation Chimney Components LFCCL-1Selecting a Location HOW to Determine Hearth Extension Requirements Floor ProtectionClearances Fireplace Installation Fireplace Installation Location Selection Chimney Installation Chimney Installation Chimney Offset Installation Chimney Offset and CAP Installation Chimney Offset and CAP Installation Chimney CAP Installation Outside Combustion AIR Precautions & Recommendations Combustion AIR Assembly GAS Appliance Installation GAS Appliance Installation Trim Installation TOP of the Fireplace OPENING. this Facing Material Must be Fireplace Operation Species Density Heat Value Maintenance and Safety DO’S DON’TS B36LA Parts Diagram and ListB36RA Appliance Installer

B36RA, B36LA specifications

The Martin Fireplaces B36LA and B36RA are sleek and stylish gas fireplaces designed to bring warmth and elegance to any living space. With their impressive features and advanced technologies, these models stand out as exceptional options for homeowners seeking both functionality and aesthetics in their heating solutions.

One of the main characteristics of both the B36LA (lean attrape) and B36RA (room attrape) is their versatile design. These fireplaces are engineered to seamlessly fit into various environments, whether in a traditional home or a contemporary dwelling. The clean, linear design allows for easy integration into different styles of decor, while the large viewing area offers an unobstructed view of the mesmerizing flames, enhancing the ambiance of any room.

The B36LA and B36RA utilize state-of-the-art venting technology, ensuring safety and efficiency. They are compatible with both direct vent and vent-free systems, providing flexibility in installation. The direct vent option allows for efficient removal of combustion gases while drawing fresh air from outside, making it a smart choice for energy-conscious homeowners. Both models also prioritize safety, featuring built-in safety mechanisms to prevent any gas leaks or hazards, ensuring peace of mind for users.

In terms of performance, the B36LA and B36RA boast impressive heating capabilities. With adjustable flame heights and a powerful heating capacity, they can efficiently warm spaces of varying sizes. The innovative burner design also creates a realistic flame appearance, mimicking the natural flicker of a wood fire, while producing minimal emissions, making them an environmentally friendly option.

Moreover, these fireplaces come equipped with advanced control options, allowing users to easily adjust settings from the comfort of their seating area. Remote control functionality and wall-mounted thermostat options make it effortless to maintain the desired temperature, ensuring a cozy atmosphere at all times.

With their combination of modern aesthetics, safety features, and advanced heating technologies, the Martin Fireplaces B36LA and B36RA present an ideal solution for those seeking both style and warmth. Whether creating a focal point in a living room or offering supplemental heat in a bedroom, these fireplaces deliver on all fronts, making them a worthwhile investment for any home.