Lopi Yankee PS manual Pellet Vent Type, Installing the Pellet Vent, Pellet Vent Termination

Page 10

1 0 Installation (For Qualified Installers Only)

Pellet Vent Type

•Must be 4" diameter Type "L" (except for masonry fireplace installations) - or - connect the

vent to a factory built type "A" chimney. All vent joints (including adapters, elbows, etc… ) must be sealed with 500° F. RTV silicone.

Installing the Pellet Vent

.RTV °F 500Silicone

Seal each vent section (including adapters, elbows, etc...) by

injecting a liberal amount of 500° F. RTV silicone into the gap

between sections.

•Horizontal sections must have a 1/4" rise every 12" of travel.

•Pellet vent connections must be sealed airtight with 500° F. RTV silicone and screwed together with at least three sheet metal screws.

Pellet Vent Termination

•Vent must terminate on the exterior of the dwelling. Horizontal terminations must protrude a minimum12" from the wall. Vertical terminations must protrude a minimum 24" from the roof surface. In addition, all clearances listed below must be met.

•Must have an approved cap (to prevent water from entering) or a 45° downturn with rodent screen.

•If the termination is located on a windy side of the house, an approved house shield is recommended to prevent soot from building up on the side of the house.

•Must not be located where it will become plugged by snow or other material.

C

H

X

A

B

H F A

E

G

F

D

NOTE: Measure clearances to the nearest edge of the exhaust hood.

AMinimum 4' clearance below or beside any door or window that opens

(This clearance may be reduced to18” if using outside air (see page 11) – we recommend the door or window be kept closed during operation.

Minimum 1’ clearance below or beside any window that does not open.

BMinimum 1' clearance above any door or window that opens

CMinimum 2' clearance from any adjacent building

DMinimum 7' clearance above any grade when adjacent to public walkways NOTE: Vent may not terminate in covered walkway or breezeway.

EMinimum 2' clearance above any grass, plants, or other combustible materials

FMinimum 3' clearance from any forced air intake of any other appliance

GMinimum 2' clearance below eaves or overhangs

HMinimum 1' clearance horizontally from combustible wall

X

Must be a minimum of 2' above the roof

© Travis Industries

4080728

100 - 01 1 5 6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Yankee Travis Industries 2IntroductionIntroduction Important Information 0 0 1 1 5Table of Contents 4Safety Precautions 100 01 1 5Safety Precautions Mobile Home6Specifications Stove Placement Installation OptionsPlanning The Installation Before You BeginClearances Straight Installation Clearances Corner InstallationVenting the Pellet Stove Maximum Venting DistancePellet Vent Type Installing the Pellet VentPellet Vent Termination Mobile Home Requirements Outside Air used for combustionRestrictor Adjustment Alcove Installation RequirementsBaffle Installation Door Seal VerificationThermostat Installation RobertshawInstallation Example Direct Through-the-wall Installation Installation Example Interior Vertical Installation Installation Example Class a Chimney Retrofit Installation Example Masonry Fireplace Hearth Stove Vertical Cap Cover Plate non-combustible Storm Collar Installation Example Freestanding Masonry Chimney Seal the coverLocation of Controls Safety Notice0Operation Starting the Heater for the First TimeLoading Pellets Operation2Two Modes of Operation 2Operation Manual ModeTo Adjust the Heat To StartAuto Mode To Adjust Room Temperature or Start the StoveAdjusting the Fan Speed 4OperationStart-Up Sequence Fault LightAuger on Light 6Operation Power OutagesUsing a Pellet/Corn Mix with This Heater Manual Auger ButtonInspect the Burn Maintenance2Daily Maintenance whenever using the stove Make Sure Pellets are Not Piling UpCleaning the Firepot 8MaintenanceCheck Firepot for Clinkers Door Opening Clearing the Auger Drop TubeClean the Hopper 0MaintenanceWeekly Maintenance or every 5 bags of pellets Clean the Heat Exchange TubesCleaning the Optional Gold Surfaces Door and optional Grill Maintenance3Clean the Baffles 2Maintenance Sweep Ash Into AshpanClean the Glass Check Ashpan, Dispose if necessaryClean the Vertical Exhaust Duct 4MaintenanceYearly Maintenance or every ton Clean the Exhaust Duct the stove must be cool and unpluggedClean the Exhaust Blower Clean the VentDoor Seal 6MaintenanceDoor Alignment Adjusting the Door Hinge and Latch Latch AdjustmentReplacement Parts Check for Air Leaks Around the Door, Glass, and AshpanNormal Operating Sounds Exhaust BlowerSafety Label Serial NoLimited 7 Year Warranty Years 1 & 2 Coverage Parts & Labor2Index

Yankee PS specifications

The Lopi Yankee PS is a remarkable freestanding gas stove that embodies elegance, efficiency, and exceptional performance. Designed for those who seek a perfect blend of traditional aesthetics and modern technology, the Yankee PS stands out as a centerpiece in any living space. One of its most notable features is its efficient heating capability. It can produce an impressive heat output, which is ideal for warming up larger rooms and open-concept living areas. The stove operates on natural gas or propane, providing versatility depending on local fuel availability.

The Yankee PS also comes equipped with a sophisticated electronic ignition system, ensuring a reliable start every time. This technology enhances user convenience, eliminating the need for matches or lighter fluids, making it a safer and more efficient option. Additionally, the stove includes an easy-to-use remote control that allows users to adjust the flame height and heat output with a simple touch, providing optimal comfort and ease of use.

Energy efficiency is another standout characteristic of the Lopi Yankee PS. With an impressive Annual Fuel Utilization Efficiency (AFUE) rating, this gas stove minimizes energy consumption while maximizing warmth in your home. This not only contributes to lower utility bills but also aligns with environmentally friendly practices.

The construction of the Yankee PS reflects quality and durability. Made with high-quality steel and featuring a ceramic glass front, the stove is designed to withstand the test of time while offering a stunning view of the flames. Its sleek design is complemented by a variety of finish options, allowing homeowners to choose a style that best fits their decor.

Safety is a top priority in the design of the Yankee PS. It comes with a robust safety screen and advanced safety shut-off systems, ensuring peace of mind during operation. These features prioritize user safety while maintaining the charm and warmth that a gas stove brings to a home.

In conclusion, the Lopi Yankee PS is an outstanding choice for those who desire a powerful yet elegant heating solution. Its combination of advanced technologies, energy efficiency, and aesthetic appeal makes it a valuable addition to any home. Whether for cozy evenings or gatherings with friends and family, the Yankee PS delivers warmth, style, and comfort.
Top Page Image Contents