Lopi 1080 owner manual Maintenance9, Yearly Service Procedure

Page 9

Maintenance9

Yearly Service Procedure

WARNING: Prior to removing the glass, shut off gas to the appliance (or remove the batteries from the battery box and shut off electricity to the fireplace). This prevents any chance of accidental burner ignition when accessing the firebox.

•Failure to inspect and maintain the fireplace may lead to improper combustion and a potentially dangerous situation. We recommend the following procedures be done by a qualified technician.

1.Remove the glass frame and log set (NOTE: the logs are very fragile - see page 11). If severely deteriorated, replace. Check the logs for sooting. A small amount of soot along the bottom of the logs is normal. If excessive sooting is found, the fireplace will require adjustment. Contact your dealer.

2.Inspect the burner and remove any debris.

•Make sure the burner is not warped, cracked, or damaged.

•Check the firebox and area around the pilot to make sure there is no warping or damage.

•If any problem is found, discontinue use and contact your dealer for service.

3.Replace the log set. Clean and replace the glasss. If the glass is damaged, replace. Make sure the gasket along the perimeter of the glass contacts the face of the firebox and forms an air-tight seal. If it does not, re-align or replace the gasket to insure an air-tight seal.

4.Start the burner. The flames should be orange/yellow and not touch the top of the firebox. If the pilot or main burners do not burn correctly, contact your dealer for service.

5.Remove any debris or vegetation near the vent termination. Contact your dealer if any sooting or deterioration is found near the vent termination.

© Travis Industries

4070710

100-01194_000

Page 8 Page 10
Image 9
Page 8 Page 10
Contents CF Fireplace Operation Maintenance2Introduction Installation WarningsIntroduction Important Information Save Your Bill of SaleFeatures Table of ContentsGas Input Specifications IntroductionIf YOU Smell GAS Safety PrecautionsBattery box or shut off gas to Wall Switch Remote Control6Operation Before You BeginThermostat Mode Manual ModeOperation Two Modes of Operation8Operation Yearly Service Procedure Maintenance9Glass Frame Removal and Installation 10MaintenanceMaintenance11 Log Set InstallationOverview Lower Rear Log 12MaintenanceUpper Rear Log Maintenance13Center Ember 14MaintenanceUpper Left Log MaintenanceLeft Twig 16MaintenanceRight Twig Maintenance1718Maintenance Ember PlacementRock Wool Placement Maintenance19 Glass CleaningBattery Installation 20Maintenance Wiring DiagramReplacement Parts List Years 1 & 2 Coverage Parts & Labor Warranty21Years 3 Through 5 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyOptional Equipment AccessoriesAndirons Trim KitOptional Equipment Index 24Index

1080 specifications

The Lopi 1080 is a high-performance wood-burning stove that epitomizes efficiency and contemporary design. One of its standout features is the large fire viewing area, which not only allows for an impressive display of flickering flames, but also enhances the overall ambiance of any living space. The 1080’s clean lines and modern aesthetics make it an attractive centerpiece in both traditional and contemporary homes.

A hallmark of the Lopi 1080 is its exceptional heating capability. It boasts a maximum BTU output of 80,000, making it suitable for heating larger areas, up to approximately 2,500 square feet. This significant heating capacity is complemented by a remarkable burn time of up to 12 hours on a single load of seasoned hardwood, making it an ideal choice for those who appreciate long, uninterrupted heat.

The stove incorporates advanced technologies for enhanced performance and efficiency. Its combustion system employs a secondary burn feature, which significantly reduces emissions by ensuring that more gases are combusted before being released into the atmosphere. This not only makes the Lopi 1080 an eco-conscious option but also reflects in reduced creosote buildup, promoting safer operation and easier maintenance.

In addition to its performance features, the Lopi 1080 includes a variety of customization options. Homeowners can choose from different finishes, such as classic black and porcelain enamel, allowing for seamless integration into existing décor. The choice of door styles and accessories also enables personalized aesthetics.

Safety is another essential aspect of the Lopi 1080, with a heat-resistant base and a built-in air wash system that keeps the glass clean for an unobstructed view. The adjustable draft control provides users with the ability to manage the burn rate and heat output effectively, ensuring optimal comfort and efficiency.

In conclusion, the Lopi 1080 is a perfect blend of innovative technology, impressive heating capabilities, and stylish design. Its focus on performance, efficiency, and safety makes it a top choice for homeowners seeking an effective and beautiful heating solution. Whether for cozy evenings or to heat your entire living space, the Lopi 1080 stands out as a remarkable wood-burning stove.
Top Page Image Contents