Regency I3100L Optional Flue Connector KIT, Masonry and Factory Built Fireplace Clearances, 165mm

Page 7

INSTALLATION

Position the grill on the inside bodyface side and fastenusingthebolts,washersandnutsprovided (2 per side) as shown in the diagrams.

Note: The grillhasafrontandrear,theholes on the front side have rounded edges and the rear holes have flat edges.

View from Rear of Insert

OPTIONAL FLUE

CONNECTOR KIT

The optional Flue ConnectorKit (Part# 846-527) and the Straight Flue Adaptor (Part #846-504) shown here, may be used to produce a secure connection between your flue connector and the insert collar. Detailed installation instructions are included with the kit.

MASONRY AND FACTORY BUILT FIREPLACE CLEARANCES

The minimum required clearances to combustible materials when installed into a masonry or factory built fi replace are listed below.

 

Adjacent

Mantle**

Top

Side

Minimum

Minimum

Minimum

Unit

Side Wall

(to Top)

Facing

Facing

Hearth

Hearth

Hearth Side

 

(to Side)

 

(to Top)

(to Side)

Extension*

Thickness*

Extension

 

A

B

C

D

E

F

G

Small Flush

 

 

 

 

 

 

 

Insert (I1100S)

15"/380mm

20"/510mm

14"/355mm

7.375"/187mm

16"/406mm

1.5"/38mm

8"/205mm

 

 

 

 

 

 

 

 

Large Flush

 

 

 

 

 

 

 

Insert (I3100L)

13"/330mm

19"/480mm

18"/455mm

6.5"/165mm

16"/406mm

1.5"/38mm

8"/205mm

 

 

 

 

 

 

 

 

Hearth Heater

 

 

 

 

 

 

 

(H2100M)

10"/255mm

25"/635 mm

14"/355mm

8.5"/216mm

18"/455mm

1.5"/38mm

6"/152mm

 

 

 

 

 

 

 

 

Side and Top facing is a maximum of 1.5" thick.

Floor protection must non-combustible, insula- tive material with an R value of 1.1 or greater.

*If the hearth extension is fl ush with the fl oor

(F)it must extend 19.5" in front of the body

face (E).

Note: Hearth Extension Width (G) is meas- ured from edge of fuel door to side of hearth.

** A non-combustible mantel may be in- stalled at a lower height if the framing is made of metal studs covered with a non-combustible board.

Clearance diagram for installations

Regency Wood Insert & Hearth Heater

7

Image 7
Contents 908-332b 06/02/06 WoodRegency Fireplace Product Table of Contents Here for your review Safety Label103 Safety Label for H2100MFireplace Specifications InstallationBefore Installing Your Insert Chimney Specifications165mm Optional Flue Connector KITMasonry and Factory Built Fireplace Clearances 375/187mmNo Cleanout Full Flue Liner Required Flue Connector BracketInstallation Into a Factory Built Fireplace Positive Flue Direct Flue Connection With CleanoutH2100M and I3100L Insert Faceplate and TrimFAN / Blower Door Handle Firebrick AssemblyBrick Flue Baffle & Secondary AIR Tube Installation Floor ProtectionHearth Heater H2100M Steel Baffle Screen DoorDraft Control Small Insert I1100SFAN Operation ALL Units Some Safety GuidelinesOperating Instructions First FireMaintenance I1100 & I3100 Main Assembly Parts List170-159 Trim Top Regular 170-911 Faceplate & Trim Set Regular 163-910170-160 Trim Right Regular 163-165 Trim Right Regular846-531 H2100 Main AssemblyI1100, I3100 & H2100 Firebrick Warranty Lifetime WarrantyInstaller Please complete the following information
Related manuals
Manual 20 pages 44.09 Kb Manual 20 pages 23.31 Kb

H2100, I1100S, I3100L specifications

The Regency H2100 and I3100L are two innovative and efficient heating solutions that cater to the evolving needs of modern homes. Known for their quality craftsmanship and advanced technology, these products have become favorable choices among homeowners seeking both aesthetics and functionality.

The Regency H2100 is a gas fireplace insert designed specifically to be installed within an existing fireplace. It features a sleek and contemporary design that enhances the ambiance of any room while providing effective heating. One of the main highlights of the H2100 model is its high efficiency rating, often exceeding 70%. This efficiency translates to reduced energy costs and a minimal environmental footprint. Equipped with a powerful heating capacity, the H2100 can effectively warm spaces up to 1,500 square feet, ensuring comfort during the coldest months.

Key technologies integrated into the H2100 include a direct vent system that allows for safe and efficient exhaust of combustion gases, promoting clean indoor air quality. Additionally, the unit features adjustable flame settings and an easy-to-use remote control, allowing for customized heating options to meet individual preferences. The H2100 also includes a variety of aesthetic options, such as different media choices, decorative surrounds, and glass doors, making it suitable for diverse interior designs.

On the other hand, the Regency I3100L is a wood-burning insert designed for homeowners who appreciate traditional heating methods. This model boasts a large firebox that can accommodate larger logs, providing extended burn times and minimal need for refueling. With an impressive efficiency rating, the I3100L minimizes wood consumption while maximizing heat output.

One of the standout characteristics of the I3100L is its large viewing glass, offering an unobstructed view of the fire, creating an inviting atmosphere. The insert features secondary combustion technology, which ensures that smoke and emissions are significantly reduced, promoting environmental friendliness. With its classic cast iron construction, durability is another crucial feature, ensuring that the insert will withstand the test of time while providing consistent warmth.

In conclusion, both the Regency H2100 and I3100L present unique heating solutions tailored to different preferences and lifestyles. With their advanced features, energy efficiency, and customizable designs, these models stand out in the market, offering homeowners the perfect blend of comfort, style, and sustainability in their heating solutions. Whether one prefers the convenience of gas or the charm of wood-burning, Regency has positioned itself as a leader in innovative heating technology.