Monte Carlo Fan Company 5OR52XXD Such as a tag, to the service panel, Downrod

SAFETY TIPS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

1.Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),

2.including fire-rated construction.

3.Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-

4.ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

5.such as a tag, to the service panel.

6.Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

7.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7

8.feet from the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and

9.use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating

10.blades.

11.Attach the mounting bracket using only the hardware supplied with the outlet box.

12.To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control. The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat- ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),

13.and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

	Phillips Screwdriver	TOOLS REQUIRED	Pliers		Step Ladder
		Wire Cutters		3
1	2

									Use metal outlet box suitable for fan support
									and use only the screws provided with the out-
	Before you begin installing the fan, Switch								let box (must support 35 lbs). Before attaching
	power off at Service panel and lock service dis-				Before installing this fan make sure the outlet box is				fan to outlet box, ensure the outlet box is
	connecting means to prevent power from being				properly installed to the house structure.			To reduce	securely fastened by at least two points to a
	switched on accidentally.			When the service dis-	the risk of fire, electric shock, or personal injury,				structural ceiling member ( a loose box will
	connecting means cannot be locked, securely				mount to outlet box or supporting system acceptable				cause the fan to wobble). Use only the
	fasten a prominent warning device, such as a				for fan support. (Mounting must support at least 35				screws provided with the outlet box.
	tag, to the service panel.				lbs.)
		Canopy disk		Downrod
4					5		Cross Pin		6
							Keeper	Yoke
	Canopy						Pin
						Loosen the 2 set screws in yoke for
						downrod to slip into yoke. Insert
						downrod into yoke on top of the Fan
	Tread leadwires and		safety cable first			Body. Align the hole in the Downrod
									Tighten the 2 Set screws on the Yoke
	through the canopy disk, Canopy and last					with the hole in the Yoke. Insert the
	the downrod.					Pin through the Yoke and Downrod			once the downrod is in place. Check
						until the point appears on the other			motor for shipping stabilizers and
						side. Install the Keeper Pin			remove if present.