19 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| House |
|
|
| Fan |
|
|
|
|
|
| ||
|
| ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Black |
|
|
|
|
|
|
|
|
| Black | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| White | |||||
| White |
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| Green(downrod) | |||||||
| Green |
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| Green(Bracket) | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Make wire connections as per above diagram. Connect the white wire from the fan to the White or Neutral wire from the power source. Connect the black wire from the fan to the Black or hot wire from the power source. Connect all Green / Yellow wires from the fan, Downrod and mounting bracket to the Ground wire from the house.
20
21
Place floating brackets onto blades aligning holes in blade with the floating bracket. Make sure that the floating bracket does not hang over the edge of blade (see insert).
22
Place blade arms onto the other side of the blade and aligning holes. Insert screws with fabric washers though the holes and tighten securely.
23
Install all 5 fan blade assemblies to the motor as shown above. Tighten screws securely.
24
Remove the 3 screws from fan.
25
Plug in electrical connection from fan into the connectors on fitter.
26
Install the 2 50 watt halogen bulbs. Do not touch bulb surface as oily residue from skin can cause the bulb to explode.
27
Use the 3 screws removed in step 21 to put fit- ter on to fan.
28
Attach shade to light kit by alignening threaded stem on light kit to hole in shade. Screw finial nut to threaded stem (do not overtighten).
29
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
Set dip switches on the Remote Transmitter and Remote Receiver to the same settings. This must be done so the units will communcate properly. If you have other fans you can set to control from one transmitter by setting both receivers the same as the transmitter. If you have more than one fan with remote. You can set the dip switches to different positiosns to have seperate control.
30
Lift Canopy to ceiling aligning the key hole slots with the screws on the bottom of the Mounting bracket. Rotate the canopy Counter Clockwise to lock in place. Tighten the screws to secure the Canopy. See inset for Keyhole shape