Fantom Vacuum FM625H owner manual Operating Instructions

Fig. 16

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

WARNING: Always remove the power plug from the wall outlet before assembling or removing accessories.

Inserting The Handle Into The Main Unit

•Insert the handle into the hole on the top of the unit. Make sure that the slot in the handle fits correctly into the opening. (Fig. 1)

•Insert the sleeve nut into the unit first. Then holding the sleeve nut with your thumb, insert the bolt. Using a flat screw driver, secure the bolt to the sleeve nut. (Fig. 1)

•To remove the handle, you have to remove the bolt and the sleeve nut.

Attaching The Hose To The Main Unit

•Hold the end of the removable hose handle and insert it into the hose connector. (Fig. 3)

Hose

Connector

Fig. 3

Inlet

Hose

Cleaning the Filter Ring

1.Around the HEPA filter there is a filter ring. This is washable in lukewarm water.

(Fig. 16) To remove the filter ring, slide it off the HEPA filter.

2.We recommend washing the filter ring when you are

washing your HEPA filter. Always allow the

filter ring to air dry for 24 hours before replacing onto the HEPA filter. Never run the vacuum without all the filters in place.

Changing & Cleaning the Exhaust Filter

The exhaust filter is a rinseable filter but should be replaced every three (3) months.

Motor Thermostat

IMPORTANT: This unit is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur:

•	Push the On/Off button once.
•	Disconnect the plug from the
	power source.
•	Check the source of overheating
	problem. (i.e. clogged hose or
	filter)
• If clogged hose or filter is found,
	unclog the hose and replace the
	filters.
•	Wait at least 45 minutes before
	attempting to reuse the vacuum.
•	After unit has cooled down for
	45 minutes, plug in the cleaner
	and push the On/Off button. The

Sleeve nut

Fig. 1

Bolt

Motorized

Floor Brush

Hose Connector

• To remove the exhaust filter covers,

push the exhaust filter covers up.

Remove the filter. (Fig. 17)

• Rinse the exhaust filters in lukewarm

water and air dry the filters completely

for 24 hours. Do not use a washing

vacuum should start again.

• If the vacuum still does not start,

contact customer service at

1 (800) 275-9251.

Attaching The Motorized Floor Brush To The Main Unit

Winding & Unwinding The Power Cord

machine to rinse the filters. Do not use

a hair dryer to dry them. Air dry only.

Never operate the vacuum without the

•Insert the motorized floor brush into its location at the bottom of the main unit, in the direction of the arrow. (Fig. 2)

•Make sure that the motorized floor brush is firmly inserted into the floor brush socket.

•Insert the inlet hose into the floor brush hose connector that is on the floor brush. (Fig. 3)

Pin

Motorized Floor

Brush ReleaseMotorized Floor

Brush Hose

Connector

Fig. 2

This vacuum cleaner is equipped with a convenient cord storage feature. The power cord winds around the two cord holders at the back of the unit. The top one has a quick

cord release feature. Turn the cord hook to the left or the right to remove the power cord. (Fig. 4)

When using the vacuum, attach the power cord to the cord holder so that the power cord is out of the way when you

are vacuuming. (Fig. 5)

Fig. 5

Fig. 4

Cord holder

exhaust filters in place.

• When the filters are

dry, replace into

the exhaust filter

covers and replace

on the vacuum.

• Severely soiled or

clogged filters should

be thoroughly rinsed with

fresh tepid water. A mild

detergent can be used

if required.

Exhaust

Filter

Cover

Fig. 17

4

9