Installing the Lwss Unit, Direct Indirect | Redring DC3810 specification

APPLIED ENERGY PRODUCTS LTD

STAINLESS STEEL UNVENTED HOT WATER STORAGE UNITS

Please read the following carefully before installation of the product. You should be competent to install the unvented system as defined by the regulations. Special attention must be paid to maintenance and service.

Please keep the unit packaged until you are ready to commence installation. Store the unit in a dry area, keep it vertical and ensure that all safety components are kept in the box.

IT IS A REQUIREMENT THAT THIS UNIT IS SERVICED AND MAINTAINED ANNUALLY – THE BENCHMARK LOG BOOK MUST BE COMPLETED AND UPDATED. FAILURE TO DO SO WILL INVALIDATE GUARANTEES.

THE DIRECT & INDIRECT UNITS

	DIRECT		INDIRECT
EXPANSION		EXPANSION
VESSEL		VESSEL
(SUPPLIED LOOSE)		(SUPPLIED LOOSE)
PRESSURE AND	HOT DOMESTIC	PRESSURE AND	HOT DOMESTIC
TEMPERATURE	WATER	TEMPERATURE	WATER
RELIEF VALVE		RELIEF VALVE
INSULATION		INSULATION	PRIMARY
INSULATION		INSULATION	TAPPINGS
			TAPPINGS
	IMMERSION		DUAL
	HEATERS		THERMOSTAT
			IMMERSION
			HEATER
COLD MAINS		COLD MAINS
VIA GROUPSET		VIA GROUPSET

INSTALLING THE LWSS UNIT

Choose a flat even surface. Wooden bearers are not essential as the unit sits on a ring stand. The unit must be installed vertically.

Please install in an area that will be accessible in the future. When first fixing take into account that the connections and controls will be front facing to facilitate access.

Check that the floor will support the unit when it is full of water. See page 14 for weights.

COLD FEED

Minimum mains pipework of 25mm MDPE or 22mm copper is advised. If 15mm copper or 1/2" lead is the only mains feed then the decision to install rests with the installer or specifier of the product. Flow rates will be compromised, even at appropriate pressures, ensure that you have at least 18 litres per minute at the bath tap. Maximum inlet pressure is 12 bar.

If multiple bath filling or showering is required, mains feed may need to be 32mm MDPE or 28mm copper.

The unit operates at 3 bar and pressures from 2 bar upwards are suitable. Lower pressure will result in a fall in flow rate. A flow rate of 20 litres per minute is a minimum requirement for single bath applications and must rise proportionately for greater demands.

DC3810 specifications

The Redring DC3810 is a standout product in the realm of electric water heating systems, designed for both residential and commercial applications. Renowned for its reliability and efficiency, the DC3810 offers users a robust solution for their hot water needs, positioned as an exceptional choice for those looking to enhance their water heating experience.

One of the main features of the Redring DC3810 is its instantaneous heating capability. This system heats water on demand, eliminating the need for a large storage tank. Consequently, users can enjoy a continuous supply of hot water without the wait, making it ideal for busy households or commercial facilities where efficiency is paramount. With a powerful heating element, this unit can quickly raise water temperatures, ensuring rapid access to hot water when needed.

The Redring DC3810 also boasts a compact design, which allows for easy installation in various locations, from kitchens to bathrooms. Its lightweight and space-saving features make it a favorite in environments where space is limited. Additionally, the unit is user-friendly, equipped with intuitive controls for setting water temperature and flow rate, giving users the flexibility to customize their hot water experience.

Incorporating advanced technologies, the Redring DC3810 operates with a high level of energy efficiency. Thanks to its capability of delivering hot water on demand, it reduces energy wastage typically associated with traditional storage water heaters. As a result, users can enjoy lower utility bills without compromising on comfort. Furthermore, the appliance includes safety features such as thermal cut-off and pressure relief valves, ensuring that it operates safely and effectively.

The unit's durable construction is another characteristic that sets it apart. Built with high-quality materials, the DC3810 is designed to withstand the rigors of daily use, resulting in a long lifespan and minimal maintenance needs. This reliability translates into peace of mind for users, knowing that they have a dependable hot water solution.

Overall, the Redring DC3810 is an impressive combination of innovative technology, user-centric design, and reliable performance. Ideal for a variety of applications, it remains a trusted choice for those who seek efficiency and convenience in their water heating solutions. Whether for residential or commercial use, the DC3810 stands out as a modern, efficient addition to any setting.