Water Boss Water Softener Controller Settings, Power Clean and Regeneration for Models 900 and 700

Page 15

Setting The 4 Button Controller

DEMAND REGENERATION

You won't have to worry about vacation settings or extra guests because the controller measures water usage and regenerates based on need. The appliance will regenerate using only the neces- sary amount of water and salt. If power has been turned off, your appliance will retain programmed settings indefinitely. See figure 9.

1) ENTERING YOUR HARDNESS SETTING

See page 12 for determining your setting number. Push the “SET” button for about 5 seconds. Now, the water hardness setting number shown in the digital readout will increase 1 grain each time you push the "CHANGE" button. After 70 grains for Model 700 (90 grains for Model 900 and 25 grains for Model 550 ) the read-out will return to 03, and continue to count up until the display num- ber matches the hardness number. Press the “SET” button to save the hardness number. To recheck the hardness, hold down the "SET" for about 5 seconds.

2) GALLONS REMAINING

After setting water hardness, gallons remaining until the next automatic regeneration is shown in the digital display. NOTE: Gallons remaining are in hundreds. 12=1,200 gallons

3) RECHARGE/REGENERATION STATUS

Regeneration cycle numbers are shown during regeneration. The read-out will flash with the cycle number. The flashing regeneration numbers are:

First cycle:

(01)

First Backwash

Second & Third cycles:

(02)

Brine/Slow Rinse

Fourth cycle:

(03)

Second Backwash

Fifth cycle:

(04)

Brine Refill

Sixth cycle:

(HO) Service

To quickly advance through the regeneration cycles, press and hold the Regenerate button for 2 seconds. Wait for the cycle to begin, after 20 seconds press and hold the Regenerate button until the cycle number changes (about 2 seconds.) Each cycle can be advanced in this manner.

4) waterMizer

The waterMizer® wheel will turn whenever water is being used. See figure 9.

5) REGENERATE

To start an immediate regeneration, press The “Regenerate” button and hold for 3 seconds. The Regenerate button is used when starting your water conditioner, to start an immediate regeneration, or to restore capacity if you have run out of salt. If your appliance has run out of salt, you may not have soft water available. Open the salt lid and add salt. Wait two hours, then press the "REGENERATE" button and hold for 3 seconds. See figure 9.

6) POWERCLEAN

The powerClean™ feature is a service/maintenance step for water supplies that have an excessive amount of iron. Activating this feature is a simple push of the powerClean™ button on the controller. PowerClean™ will appear in the display when this feature is activated. The appliance will regener- ate every other day with five pounds of salt. Leave the powerClean™ feature on for a minimum of two weeks. The frequent regeneration will elimate iron buildup in the resin bed. The use of salt with an iron cleaning agent or iron out cleaner is recommended for continuous use as a preventive measure against iron fouling of the resin bed. To deactivate this feature, simply press the powerClean™ button. Use this feature every six months as a part of your routine maintenance pro- cedure to insure a long service life for your water treatment appliance. See figure 9.

13

Image 15
Contents Installation Table of Contents Questions How To Get The Maximum Efficiency From Your Appliance Checklist Before Installation Some DOS Do’s And Don’tsReference Illustrations Installation GuidePlumbing Connections Installation TIP Connecting Drain LineBypass Position Service Position Plugging in Transformer Adding Salt to the Brine Cabinet Regeneration cycles CyclesInstallation And Start-Up Procedures Waterscreen Demand Regeneration Setting The 4 Button ControllerAdvanced Customer Settings Setting The ControllerProgramming is NOW Complete PART# Description Quanity Care, Maintenance and PartsCabinet and Assemblies Injector Assembly O Adapter Assembly Drive End Cap Assembly Brine Valve Housing Assembly Safety Shutoff Assembly Brine Valve Elbow Assembly Bottom Fill Plug Assembly Model # Specifications/Capacity ChartProblem Cause Solution TroubleshootingWith 12 VAC present at controller, replace circuit board Call For Return Information Limited WarrantyPage WaterBoss P.O. Box 298, Groveport, OH

900, 700, 550 specifications

The Water Boss series, specifically the models 900, 700, and 550, represents a cutting-edge advancement in household water treatment technology. These water softeners and filters have been designed to address the most common water issues faced by homeowners, including hard water, sediment, and other contaminants.

One of the standout features of the Water Boss 900, 700, and 550 is their efficient ion exchange process, which removes hardness minerals such as calcium and magnesium. The 900 model showcases a robust capacity, ideal for larger households, with the ability to handle up to 32,000 grains. Similarly, the 700 model is tailored for medium-sized families, effectively managing up to 24,000 grains. The 550 is perfect for smaller households, providing a capacity of 18,000 grains. This range ensures that homeowners can find a model suited to their specific needs, optimizing water quality without excessive wastage.

Each model incorporates advanced technologies such as a microprocessor-controlled regeneration process that ensures the system only regenerates when necessary. This feature not only saves salt and water but also reduces operating costs, making them economical choices over time. The pre-programmed cycles and flow meters further enhance efficiency by allowing users to track water usage accurately, ensuring the system operates within optimal parameters.

Regarding construction, these models boast durable, corrosion-resistant tanks designed for longevity, while also including a built-in app that provides real-time diagnostics and alerts. This connectivity allows users to monitor their water quality and system status remotely, ensuring timely maintenance and interventions when necessary.

Furthermore, the Water Boss series stands out with its compact design, making it an excellent choice for installations in tight spaces. They also feature easy-to-read LED displays that make navigation simple for users of all experience levels.

Environmental considerations are also paramount; the Water Boss systems utilize eco-friendly methods to minimize salt usage and energy consumption, contributing to a more sustainable household.

In summary, the Water Boss 900, 700, and 550 models deliver efficient, reliable, and environmentally conscious water treatment solutions. With their advanced features, user-friendly interfaces, and focus on sustainability, these systems ensure that households have access to clean, softened water, enhancing daily life while contributing to resource conservation.