SECTIONAL DOOR SYSTEMS
T H E R M O S PA N ® | 2 0 0 - 2 0 | ||||||||
Note to specifiers: Words in parentheses indicate frequently specified and highly recommended options. | |||||||||
PART I – GENERAL |
| 1.07 | A. | Delivery, Handling, Storage |
| D. | Counterbalance: | ||
1.01 | Section Includes |
|
| Deliver products in manufacturer’s original containers, |
| 1. Springs shall be torsion | |||
A. | Sectional overhead doors [manually] [motor] |
| B. | dry,undamaged,seals and labels intact. |
|
| |||
1.02 | operated with accessories and components. |
| Store and protect products in accordance with |
| minimum [25,000 standard] [50,000] [100,000] | ||||
Related Work |
| 1.08 | manufacturer’s recommendations. |
|
| cycles of use,on continuous steel [solid]. | |||
A. | Opening preparation, miscellaneous or structural steel | Warranty |
|
| 2. Spring fittings and drums made of die cast,high | ||||
| work, access panels finish or field painting are in the |
| A. | Provide manufacturer’s standard SEVENYEAR warranty |
| strength aluminum. | |||
| scope of work of other trades and divisions of these |
|
| against separation/degradation of the polyurethane |
| 3. | |||
1.03 | specifications. |
|
|
|
| foam from the steel skin of the panel under provisions | 2.03 | provide a minimum of a 5:1 safety factor. | |
Reference Standards |
|
|
| of Section 01700. Standard manufacturer’sTENYEAR | Operation | ||||
A. | ANSI/DASMA 102 – American National |
|
| warranty against cracking,splitting or deterioration due | A. Operation shall be [manual | ||||
| Standards Institute [A216.1] Specifications for sectional |
|
| to |
| [motor] [motor with chain hoist]. Manufacturer does | |||
| overhead doors published by Door & Access Systems | PARTII – PRODUCTS |
|
| not recommend chain hoists or jack shaft operators | ||||
| Manufacturers Association, International in bulletin |
|
| on the following track applications. | |||||
B. | – Zinc | 2.01 | Manufacturer |
|
| •15" radius standard lift with roof pitch less than 2:12 | |||
ASTM A123 |
| A. |
| ||||||
C. | coatings on iron and steel products. |
|
|
| |||||
ASTM A216 | – Specifications for sectional overhead |
|
| construction complete as specified in this section and |
| •Low headroom track | |||
D. | type doors. | – Steel wire, |
|
| as manufactured by |
| Special chain hoist assemblies (using a trolley rail) | ||
ASTM A229 | 2.02 | Hope,Ohio. |
| 2.04 | are available for the above track systems. | ||||
E. | mechanical springs. |
| Materials |
| Locks | ||||
ASTM |
| A. | Door Sections:Shall be of steel/polyurethane/steel | A. Locks shall engage the | |||||
| [galvanized] by the |
|
| sandwich type construction with thermal break and |
| utilize [an interior side lock] [standard size rim cylin- | |||
F. | commercial quality. |
|
|
| calculated materials“R”- value of 17.50,in accordance | 2.05 | der]. | ||
ASTM D1929 – Ignition temperature test to |
|
| with industry guidelines. |
| Weatherstripping | ||||
| determine flash and ignition temperature of |
|
| 1. Exterior Skin:Structural | A. Doors shall be equipped with top and side seals | ||||
G. | foamed plastics. |
|
|
| steel,20 gauge white flush smooth. |
|
| to seal against header, | |
ASTM |
|
| 2. Interior Skin:Structural |
| joint seals between sections, and vinyl “bulb” | ||||
and smoke developed index. |
|
|
| steel,factory finished with a polyester primer and |
| shaped astragal provided on the bottom | |||
H. | ASTM E330 | – Structural performance of exterior |
|
| white finish coat. Interior skin shall have two 13/4" | 2.06 | section. | ||
| windows,curtain walls,and doors by uniform static air |
|
| Glazing | |||||
I. | pressure difference. |
|
|
| rib caps per section. |
| A. | Optional. | |
ASTM |
|
| 3. Ends of section shall be sealed with 18 or 16 | 2.07 | Windload | ||||
J. | Acoustical performance value = 23 |
|
|
| [14 GA.] gauge | A. Windload – per DASMA | |||
ASTM |
|
| height end caps. |
|
| local codes. | |||
K. | class. Acoustical performance value | = 22. |
|
| 4. Insulation:Cavity shall be filled with | PARTIII – EXECUTION | |||
ASTM E283 | = .07CFM/FT2 at 15 |
|
| CFC free polyurethane core separated by a factory | |||||
1.04 | MPH. |
|
|
|
| extruded thermal break. |
| 3.01 | Installation |
Quality Assurance |
|
|
| 5. Insulated sections shall be tested by an I.C.B.O. | A. | General: | |||
A. | Sectional overhead doors and all accessories and |
|
| certified laboratory in accordance withASTM |
| 1. Install doors in accordance with | |||
| components required for complete and secure |
|
| 91A and shall achieve a Flamespread Index of 10 or |
| manufacturer’s instructions and standards. | |||
| installations shall be manufactured as a system from |
|
| less,and a Smoke Developed Index of 210 or less. |
| Installation shall be by an authorized | |||
B. | one manufacturer. |
|
|
| 6. Insulation material shall be tested by an I.C.B.O. |
|
| ||
Sectional overhead doors shall be tested and labeled |
|
| certified laboratory in accordance withASTM |
| 2. Verify that existing conditions are ready to receive | ||||
| certifying compliance withASTM D1929 andASTM |
|
|
| sectional overhead door work. | ||||
1.05 |
|
|
|
| temperature of 734 degrees F,and a minimum Self |
| 3. Beginning of sectional overhead door work means | ||
Systems Description |
|
|
| Ignition temperature of 950 degrees F. | B. | acceptance of existing conditions. | |||
A. | Sectional Overhead Door:Type: |
|
|
| 7. Insulated sections shall be tested and meet all | Install door complete with necessary hardware,jamb | |||
B. | Thermospan |
|
| B. | requirements of the UBC |
| and head mold strips, anchors,inserts, | ||
Mounting:Continuous angle mounting for [steel] |
| Track:Track design shall be [standard lift] [high lift] |
| hangers,and equipment supports in accordance with | |||||
C. | [wood] jambs |
|
|
|
| [vertical lift] [low headroom].Vertical mounting angles |
| final shop drawings,manufacturer’s | |
Operation:[manual |
|
| shall be |
| instructions,and as specified herein. | ||||
D. | [motor] [motor with chain hoist] |
|
|
| [3"].Vertical track shall be graduated to provide wedge | C. Fit,align and adjust sectional overhead door assemblies | |||
Material:Galvanized steel with polyester finish paint |
|
| type weathertight closing with continuous angle mounting |
| level and plumb for smooth operation. | ||||
E. | Insulation:Polyurethane |
|
|
| for [steel] [wood] jambs,and shall be fully adjustable to | D. Upon completion of final installation,lubricate,test and | |||
1.06 | Submittals |
|
|
|
| seal door at jambs. Horizontal track shall be reinforced |
| adjust doors to operate easily,free from warp,twist or | |
A. | Shop Drawings:Clearly indicate the following: |
|
| with continuous angle of adequate length and gauge to |
| distortion and fitting for entire perimeter. | |||
| 1. Design and installation details to withstand |
|
| minimize deflection. |
|
| Note:Architect may consider providing a | ||
| standard windload. |
|
|
| Note: Horizontal track applies to standard lift,high lift, |
| schedule when more than one sectional | ||
| 2. All details required for complete operation |
| C. | low headroom and | 3.02 | overhead door or opening type is required. | |||
| and installation. |
|
| Hardware:Hinge and RollerAssembly: |
| Materials (See note above.) | |||
| 3. Hardware locations. |
|
|
| 1. Hinges and brackets shall be made from |
|
| ||
| 4. Type of metal and finish for door sections. |
|
|
|
|
| |||
| 5. Finish for miscellaneous components |
|
| 2. Track rollers shall be |
|
| |||
B. | and accessories. |
|
|
| races with |
|
|
| |
Product Data:Indicating manufacturer’s product |
|
| 3. All factory authorized attachments shall be made at |
|
| ||||
| data,and installation instructions. |
|
|
| locations indicated and reinforced with backup plates. |
|
| ||
Specifications and technical information also available at www.arcat.com, SpecWizard™, and Sweets.com®.
Distributed By:
Item #332537 Revised 9/2007 | |
For technic l i formation, visit: | Printed in U.S.A. |
| |
© 2007 |
|
Mt. Hope, OH • Dalton, OH • Trail, OH • Pensacola, FL • Portland, OR |
|