Bulb Installation, Wire the Light Control

INSTALLATION

For easy installation, select an existing light operated by a wall switch for replacement.

For best performance, mount the ﬁxture about 8 ft. (2.4 m) above the ground.

CAUTION: Keep the sensor at least 1" (2.5 cm) away from the lamps.

CAUTION: To Avoid Fire Or Burn Hazards:

•Allow ﬁ xture to cool before touching. The bulb and the ﬁ xture operate at high temperatures.

•Keep ﬁ xture at least 2" (5 cm) from combustible materi- als. Do not aim at objects closer than 3 feet. (1 m).

•Use only T3, 150W (max.) tungsten halogen 120 VAC lamps.

For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock. Also for proper under eave operation, remove the protective backing from the Light Shield and stick on as shown below.

For eave mount only:

❒Swing the sensor head towards the clamp screw joint.

Controls

Clamp Screw

❒Then rotate the sensor head clockwise 180° so the controls face down.

Controls

Light Shield

Opening

Controls

If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done.

BULB INSTALLATION

NOTE: Lamps are included, but you will need to install them

NOTE: When re-lamping, turn power off and let the ﬁ xture cool.

❒Open glass covers.To remove the old bulb push the bulb towards the right (with ﬁ xture as shown) until the left side of the bulb is clear of the left socket.

❒To install a bulb, push the bulb into the right socket so the bulb ﬁ ts completely into the left socket.

❒Check that the bulb is seated properly.

❒Close the glass covers.

WIRE THE LIGHT CONTROL

WARNING: Turn power off at circuit breaker.

❒Remove the existing light ﬁ xture.

❒Install mounting strap to junction box using screws appropriate for your junction box.

❒The plastic hanger can be used to hold the ﬁ xture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap.

❒Thread all ﬁ xture wires through the large holes in the gasket as shown.

❒Connect the junction box wires to the light ﬁ xture wires as shown. Twist together and secure with wire connectors.

White to White

Black to Black

Gasket

Rubber Plug

Mounting

Bolt

Connect any ﬁxture ground wire(s) and the cover plate ground screw to the junction box ground wire.

MOUNT THE LIGHT CONTROL

❒Place the Mounting Bolt through the front of the junction box cover. Push the small gasket hole over the Mounting Screw.

❒Make sure the wire connectors and wires are inside the junction box. Align the Mounting Screw with the center hole in the Mounting Strap.Secure the ﬁxture to the Mounting Strap.

Push the Rubber Plug over the mounting screw.

Keep lamps at least 1" (2.5 cm) from the sensor.

❒Push the Rubber Plug ﬁ rmly into place.

❒If not installed on a weatherproof box, caulk the wall plate and mounting surface with silicone

❒Adjust the lamp holders by loosening the lock nuts but do not rotate the lamp holders more than 180° from the factory setting.

2	598-1275-00

5512 specifications

Desa 5512 is an innovative community that combines modern living with sustainable practices, making it a pioneering model for future urban planning. Situated in a strategic location, this community integrates luxurious amenities with cutting-edge technologies to provide residents with a unique lifestyle experience.

One of the main features of Desa 5512 is its design, which emphasizes open spaces and green areas. The community is characterized by well-planned streets, pedestrian pathways, and parks, encouraging outdoor activities and a connected lifestyle. These features not only create a healthier environment but also foster social interactions among residents, promoting a sense of belonging and community spirit.

The technological advancements incorporated into Desa 5512 are noteworthy. Smart home technology is a hallmark of this community. Homes are equipped with automated systems that allow residents to control lighting, heating, and security remotely via smartphone applications. This convenience enhances everyday living and contributes to energy efficiency, aligning with the community's sustainable goals.

Another significant characteristic of Desa 5512 is its focus on renewable energy. The community utilizes solar panels on rooftops and common areas, harnessing the sun's power to reduce dependency on traditional energy sources. This initiative not only lowers utility costs for residents but also serves as a model for environmental responsibility.

Transportation within Desa 5512 is designed with sustainability in mind. The community features bike-sharing programs and electric vehicle charging stations, promoting eco-friendly commuting options. Public transportation links are also conveniently accessible, making it easy for residents to commute to nearby urban centers without relying on personal vehicles.

Desa 5512 prioritizes safety and security, incorporating advanced surveillance systems and smart security features. Residents can feel secure knowing that their community is equipped with up-to-date technology to ensure their safety.

In terms of community engagement, Desa 5512 hosts regular events, workshops, and seminars aimed at fostering a vibrant community culture. These initiatives encourage residents to participate in local governance, sustainability practices, and recreational activities.

Overall, Desa 5512 exemplifies a forward-thinking approach to community development, balancing modern conveniences with environmental stewardship. Its innovative features, commitment to sustainability, and emphasis on community make it a standout model for future residential living.