CAT.CO250B
CO
FRONT |
| SIDE | BACK | ||||||||
VIEW |
| VIEW | VIEW | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4.25”
1.6”
ARCHITECTURAL AND ENGINEERING SPEC
The carbon monoxide alarm shall be a BRK Model. CO250 and shall provide at a minimum the following features and functions:
1.An electrochemical CO sensor.
2.The unit shall be capable of self restoring.
3.The unit shall have an "End of Life" signal. This signal should be capable of temporarily being silenced for up to 2 days. After about 2 days, the signal will resume. After about
4.Powered by a supervised 9V battery and a solid state piezo horn rated at 85dB at 10 ft.
5.A visual LED
6.A full function test button. The test button should check all alarm functions by stimulating the chamber to simulate a CO condition, causing the unit to alarm. Model CO250 also has a silence feature to silence unwanted nuisance alarms.
7.A tamper resistant locking pin that locks alarm cover to prevent removal of battery.
8.The CO sensor is adjusted not to detect CO levels below 30 PPM and will not alarm when exposed to constant levels of 30 PPM for 30 days. It will alarm at the following levels: 400 PPM CO between 4 and 15 minutes, 150 PPM CO between 10 and 50 minutes and 70 PPM CO between 60 and 240 minutes.
9.The unit shall be capable of operating between 40°F (4°C) and 100°F (38°C) and relative humidity between 10% and 95%.
10.The unit shall contain mounting hardware and shall be listed for wall or ceiling mounting.
11.The unit shall at a minimum meet the requirements of UL2034, NFPA 720, NFPA 101, ICC.
INSTALLATION OF ALARM
Installation of this CO alarm must conform to NFPA 720. Always check your local building codes. Follow all instructions for placement as outlined in the user’s manual in sections titled “Recommended Locations for
CO Alarms” and “Locations to Avoid for CO Alarms”.
1
TECHNICAL SPECS
Alarm Dimensions: | 4.25” dia x 1.6”H |
Weight: | 5.1 oz. |
|
|
Operating Volatage: | 9V Battery Powered |
|
|
Temperature Range: | 40F (4C) to 100F (38C) |
|
|
Humidity Range: | 10% to 95% relative humidity (RH) |
|
|
Audio Audio Alarm: | 85dB at 10 feet |
Test/Silence: | Electronically simulates smoke condition, |
| causing the unit to alarm and silences unit. |
Alarm Reset: | Automatic when carbon monoxide clears |
|
|
CO Sensor: | Electrochemical |
|
|
Indicator Lights: |
|
DC Power: | Intermittent Red Light |
|
|
Listing: | Listed to UL2034 Standard |
SHIPPING SPECS:
Individual Carton Dimensions | 4.38 ”L x 1.75”W x 4.38”H |
Weight | 0.39 lbs. |
Cube | 0.02 ft3 |
UPC | 0 29054 00392 8 |
|
|
Master Carton Dimensions | 9.2 ”L x 5.55”W x 5.1”H |
Master Pack | 6 |
Weight | 3.2lbs. |
Cube | 0.15 ft3 |
I2 of 5 | 600 29054 00392 0 |
|
|
Pallet Information |
|
Cases per Layer | 36 |
Number of Layers | 9 |
Cases per Pallet | 324 |
Units per Pallet | 1,944 |
Cube | 55.0 ft3 |
Weight | 1,107 lbs. |
2
3
4
6 5
7
The parts of this CO alarm
1."Open Here"
2."No Battery" tab
3. Test/Silence button
4. CO alarm base
5. Mounting slots
6.Install 9V battery here
7.Locking pin slot
8.Locking pin: Remove and insert in 7
brkelectronics.com
7
8
©2009 BRK Brands, Inc. a Jarden Corporation Company (NYSE: JAH)
3901 Liberty Street Road
Aurora, IL
First Alert is a registered trademark of the First Alert Trust BRK is a registered trademark of BRK Brands, Inc. CM2925