Pitco Frialator L80-029 installation instructions Troubleshooting

Page 14

TROUBLESHOOTING

Should there be a problem with your appliance, use the following tables to isolate possible faults before calling Pitco Technical Support.

PROBLEM

 

POSSIBLE CAUSES

 

CORRECTIVE ACTION

 

 

 

 

 

 

A.

Main breaker in OFF position.

A.

Turn on Circuit Breaker to appliance.

Appliance will not

B.

Gas supply turned OFF.

B.

Turn on gas supply to appliance.

C.

Appliance unplugged.

C.

Plug appliance power cord into wall outlet.

run, front panel

D.

Blown control fuse.

D.

Refer to Service and Parts manual for your appliance to

lights are not ON.

E.

Faulty transformer.

E.

 

properly diagnose and correct these problems.

 

F.

Defective controller.

F.

 

 

 

A.

Tripped hi limit

A.

Depress red button and reset hi limit.

Appliance will not

B.

Controller is not turned on

B.

Turn controller on.

C.

SCBS thermal limit switch has

C.

 

run, front panel

Depress button on thermal limit switch and reset.

lights are ON.

 

tripped

 

 

D.

Faulty temperature probe

D.

Refer to Service and Parts manual to diagnose and correct

 

 

E.

Defective controller.

E.

these problems.

 

A.

Unplugged wire harness.

A.

Verify that all wires and harnesses are plugged in properly

 

 

 

 

to the correct component.

Appliance is ON, but

B.

Improper wiring.

B.

Verify that the wiring steps in this instruction have been

 

 

 

followed correctly. Correct any faulty wiring.

a Cleaning Cycle

C.

Faulty SCBS Board

C.

Replace SCBS Board.

does not execute

D.

Faulty SCBS Valve

D.

Replace SCBS Valve.

 

E.

Clogged SCBS Orifice

E.

Clean debris from SCBS orifice opening.

 

F.

Poorly aligned or faulty SCBS

F.

Check that the SCBS Lighter arm has been properly

 

 

Lighter arm.

 

installed. Replace if faulty.

SCBS energizes

A.

Faulty SCBS Board

A.

Replace SCBS Board.

beyond normal cycle

 

 

 

 

parameters (during

 

 

 

 

cooking, idling, etc.)

B.

Faulty SCBS Valve

B.

Replace SCBS Valve.

 

 

 

 

 

 

A.

Pilot tubing is loose.

A.

Ensure pilot tubing is tight and properly connected.

 

B.

Pilot is mounted improperly.

B.

Ensure that pilot is mounted properly.

 

C.

Flame sensor is misaligned.

C.

Ensure that the flame sensor is properly aligned.

Appliance will not

D.

Low Pilot

D.

Ensure that pilot is adjusted to provide adequate flame.

E

Clogged Pilot orifice

E

Ensure that pilot orifice is clear of debris.

run, control flashes

F.

Damaged or defective Pilot.

F.

Replace pilot if necessary.

ignition failure

 

 

 

Reset Thermal Limit switch. On models MG2 and MG2T,

 

 

 

 

 

G.

SCBS Thermal Limit switch has

G.

verify that flue baffles.are properly adjusted per these

 

 

tripped.

 

instructions. Check ventilation hood for improper

 

 

 

 

operation, down draft or blockage.

Appliance will not

A.

Faulty temperature probe

A.

Refer to Service and Parts manual to diagnose this problem

maintain

 

 

 

and replace temperature probe.

temperature

B.

Faulty hi limit switch

B

Refer to Service and Parts manual to diagnose this problem

properly.

 

 

 

and replace hi limit switch.

 

A.

Blockage in burner tubes.

A.

Ensure that burner tubes are free of obstructions.

Thermal Limit

B.

Flue is blocked

B.

Ensure that flue is free of obstructions.

Switch trips after

C.

Model MG2 or MG2T flue baffle

C.

Refer to flue baffle adjustment procedure in these

short period of

is set too restrictively.

instructions to set flue baffle to a less restrictive setting.

operation.

D.

Ventilation hood malfunction

D.

Check ventilation hood for improper operation, down draft

 

 

 

 

or blockage.

L80-029 Rev 5 10/07

12

Image 14
Contents Pitco Retain These Instructions for Future Reference L80-029 Rev 5 10/07 Page Page Page Page Page Older Revision Board Shown NEW Revision Page L80-029 Rev 5 10/07 Page Less Restrictive More Restrictive Troubleshooting L80-029 Rev 5 10/07 L80-029 Rev 5 10/07 L80-029 Rev 5 10/07 L80-029 Rev 5 10/07 L80-029 Rev 5 10/07 L80-029 Rev 5 10/07 L80-029 Rev 5 10/07 L80-029 Rev 5 10/07

L80-029 specifications

The Pitco Frialator L80-029 is a high-performance commercial deep fryer designed to meet the demanding needs of restaurants and food service establishments. With its robust construction and innovative design, the L80-029 is suited for frying a wide variety of foods, from French fries to chicken wings, ensuring consistent quality and temperature control.

One of the main features of the L80-029 is its efficient heating system which utilizes a set of powerful burners. These burners are designed to deliver high BTU output, allowing the fryer to reach optimal cooking temperatures quickly. This capability not only enhances cooking efficiency but also helps reduce oil absorption in foods, resulting in healthier fried products.

The L80-029 is equipped with a unique heating element that is positioned below the fry pot. This design minimizes cold spots and ensures even heating throughout the oil, leading to perfectly cooked items every time. This fryer also incorporates a reliable temperature control system that maintains precise frying temperatures, critical for achieving the desired texture and flavor in fried items.

Another significant characteristic of the Pitco L80-029 is its convenience and ease of use. The fryer comes with adjustable legs, making it simple to position in any kitchen layout. The front-mounted thermostat and easy-to-read indicators provide users with intuitive operation and oversight of the cooking process. This user-friendly design allows kitchen staff to operate the fryer effectively without extensive training.

Safety features are integral to the design of the L80-029. It includes a high-limit switch that prevents overheating and potential hazards, safeguarding both the equipment and operators. The fryer's stainless-steel construction not only enhances its durability but also simplifies cleaning and maintenance, ensuring a long lifespan even in the busiest of kitchens.

Furthermore, the Pitco Frialator L80-029 is designed with energy efficiency in mind. The efficient heat transfer and oil management technology help to reduce overall operating costs while maintaining high frying performance.

In summary, the Pitco Frialator L80-029 stands out in the commercial cooking equipment market due to its powerful heating system, ease of use, safety features, and energy-efficient design. These attributes make it a reliable choice for any kitchen looking to deliver high-quality fried foods efficiently and consistently.