Beckett NX manual Start the Burner and Set Combustion, Wiring Connections Diagram

Page 7

Start the Burner and Set Combustion

The burner is supplied with either a one-stage pump or a two-stage pump based on the oil supply system requirements. Consult the instructions pro- vided with the pump for installation specifications.

When installing a one-pipe system, connect the inlet line to the pump inlet. The fuel pump may be installed with gravity feed or lift. The maximum al- lowable lift for a single pipe installation is 8 ft.

When installing a two-pipe system, remove the 1/16” pipe by-pass plug from plastic bag attached to fuel unit. Remove 1/4” plug from return port. Insert and tighten the by-pass plug. Attach return and inlet lines. The return line should terminate ap- proximately 3 to 4” above supply line inlet. Failure to do this may introduce air into the system and could result in loss of prime.

•Wiring Connections Diagram

Refer to the appliance manufacturer’s wiring dia- gram prior to connecting the burner wiring. All wir- ing must be in accordance with the latest revision of National Electric Code NFPA 70 and all local codes and regulations.

The R7184 primary control with valve-on delay and burner motor-off delay, shown in Figure 4, requires a constant 120 volt AC power source supplied to the black wire on the control. (Refer to the appli- ance manufacturer’s instructions.) The red wire goes to the appliance limit circuit. Please note that other control manufacturers may use different wire colors for power and limit connections.

Figure 4a. – Typical Burner Control Wiring

Refer to the appliance manufacturer’s wiring diagram for actual specifications.

RWB 6104 BNX R02

Page 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Potential for Fire, Smoke and Asphyxiation Hazards To the Professional, Qualified Installer or Service AgencyTo the Homeowner or Equipment Owner Information To Be Used Only By Qualified Service Technicians Table of ContentsGeneral Information To the Owner General InformationHazard Definitions Inspect Chimney or Direct Vent System Required Inspect/Prepare Installation SiteGeneral Specifications Burner Specifications Clearances to Burner and ApplianceDirect/Sidewall Venting Application Inspect/Prepare Installation SiteFuel Line Installation Combustion Air Supply InformationMount Burner on Appliance Prepare the BurnerGeneral Low Firing Rate Baffle If specifiedStart the Burner and Set Combustion Wiring Connections DiagramStart the Burner and Set Combustion Start-up and Initial SettingsStart Burner and Set Combustion NX Burner with Low Fire Rate Baffle Lfrb InstalledNX Burners Set Combustion with Test Instruments Trained Service Technician’s Regular MaintenanceTrained Service Technician’s Regular Maintenance Cover InstallationIng Windows Check/Adjust Electrodes Nozzle InstallationRetention Head/Throttle Cup Alignment Check/Adjust Zero CalibrationBlower wheel assembly Blower Wheel Replacement Replacement Parts List Replacement Parts DiagramLimited Warranty Information Warranty

NX specifications

Beckett NX is a cutting-edge oil burner that exemplifies energy efficiency and reliability in heating systems. Designed for both residential and commercial use, the Beckett NX system is engineered to optimize performance while minimizing energy consumption and emissions.

One of the standout features of the Beckett NX is its advanced combustion technology. It utilizes a precision-designed nozzle that ensures a fine mist of oil is atomized for optimal combustion. This not only enhances efficiency but also significantly reduces smoke and particulate emissions, making it an environmentally friendly choice in today’s market. The system is equipped with diagnostic capabilities that allow for easy troubleshooting, enabling users to monitor performance and quickly address any potential issues.

Another significant characteristic of Beckett NX is its compact design, which allows it to fit seamlessly into various heating systems without requiring extensive modifications. This makes it an ideal solution for both new installations and retrofitting existing systems. The burner is also designed for quiet operation, reducing noise levels compared to traditional models and ensuring a more comfortable indoor environment.

In terms of safety, the Beckett NX incorporates numerous features to ensure reliable operation. It includes a burner control that monitors flame stability and combustion quality, providing real-time feedback. With built-in safety mechanisms, such as a flame safeguard, the system minimizes risks associated with malfunctioning equipment.

The technology behind Beckett NX also embraces modern connectivity options. The burner can be integrated with smart home systems, allowing users to adjust settings remotely and monitor heating performance through dedicated apps or interfaces. This level of control empowers homeowners and business operators alike to enhance their heating efficiency further.

Finally, the Beckett NX is designed for longevity and ease of maintenance. Its modular components allow for straightforward access, simplifying routine servicing and reducing downtime. With a robust build quality that withstands the rigors of daily use, the Beckett NX promises durability and reliability for years to come.

In summary, Beckett NX stands out in the heating industry for its combination of advanced combustion technology, compact design, safety features, smart connectivity, and ease of maintenance. These characteristics make it a leading choice for those seeking an efficient and effective oil burner solution, ensuring homes and businesses stay warm while being mindful of environmental impact.
Top Page Image Contents