MODEL 5394
MODELO 5394
OPERATION (Figures 1 and 2)
The Heater may be operated by the manual controls located on the Heater (as shown in Figure 1) or by your remote control (shown in Figure 2).
1.Place the Heater on a firm, level surface, after assembling per this manual.
CAUTION: Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Re- ceptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater.
3. | When the Heater is initially plugged in, there will be a ‘beep’ and |
| the power light will come on indicating that there is power to the |
| unit. The power light will remain lit until the Heater is unplugged |
| from the electrical outlet. |
4. | Turn the Heater ON by pressing the ( ). |
Timer Function:
The timer function will work in any mode. The timer function al- lows you to set the length of operation from 1 hour to 8 hours. Pressing the Timer Button (
) will increase the length of opera- tion by 1 hour each time the button is pressed. Pressing the Timer Button (
) once more after the display reflects 8 hours will reset the Heater to continuously running. Once the timer has been set, the timer will count down the hours in 1 hour increments, showing on the display the remaining operating time. The Heater will turn itself off when the set time has elapsed. The unit can be turned back on by pressing the Power Button (
).
AUTOMATIC TEMPERATURE CONTROL
The automatic temperature function will only operate on "High" heat ( 
). You cannot set the temperature automatically when the unit is in the low heat mode.
1. | To set the room at a specific temperature press the ( ) or ( ) |
| buttons to the desired temperature. The display will now reflect |
| the ( ) and the temperature will be flashing. The Heater is now |
| in Auto Temperature Mode. |
2. | When you reach the temperature at which you want to set the |
| unit, the set temperature will flash several times and then the |
| display will return to indicate the current room temperature and |
| will gradually change as the room temperature changes. NOTE: |
ARMADO (Figuras 1 a 6)
Herramientas Necesarias: Destornillador de Cabeza #2 Phillips (no incluido)
Retire cuidadosamente el Calefactor de su bolsa y caja. Para facilitar el armado, coloque el Calefactor de manera que la parrilla frontal y el panel de control den hacia arriba.
(8) - M5 X 13mm (2) - M4 X 13mm
Tamaño Real De Tornillos
Figura 1
1.Coloque el Cable Eléctrico en la parte inferior del Calefactor. Pase el Cable Eléctrico por el centro del Conjunto de Soporte de Columna.
2.Una el Conjunto de Soporte de Columna a la Base del Motor con (4) tornillos M5 X 13mm. Cerciórese de que la Llave que está en la Base del Motor quede alineada con la Muesca de Ubicación en el Conjunto de Soporte de Columna. (Figura 2)
4.Fije las mitades de la base con (2) tornillos M4 X 13 mm. Pase el Cable Eléctrico por el gran orificio que se encuentra del Conjunto de la Base. NOTA: El canal para cable en la parte inferior de la base debe estar hacia la parte posterior del Calefactor.
(Figure 4)
Cable
Eléctrico
Conjunto de 
la Base 
Cable
Eléctrico
Figura 4
5. | When initially turned on, the Heater will display the current | ||
| room temperature in ° Fahrenheit. Press the ( ) and ( |
| ) but- |
|
| ||
| tons at the same time to change the display to ° Celsius. Press | ||
| the same two buttons together again to change the display | ||
| back to ° Fahrenheit. The Heater will be in HIGH ( ) heat (1500 | ||
| Watts). | ||
6. | Upon turning the Heater on, the unit will be in HIGH heat ( ) (1500 | ||
| Watts) and will display the current room temperature. | ||
7. | Pressing the ( ) at this point will set the Heater into LOW ( ) | ||
| heat. | ||
8. | To turn the Heater OFF, press the ( ) and unplug the unit from | ||
| the electrical outlet. | ||
View of Control Panel
Figure 1
The oscillation function will work in any mode. Pressing the (
) will allow the Heater to oscillate back and forth. To stop the oscillation, press the (
) once more.
| the temperature display does not indicate the temperature of |
| the heated air being emitted by the heater. |
3. | Once the room temperature reaches 2 degrees above the set |
| temperature, the Heater will shut off. Once the room tempera- |
| ture reaches 1 degree below the set temperature, the Heater |
| will turn back on and continue to cycle off and on to maintain |
| the set temperature. |
4. | This function will cancel if the ( ) button is pressed. The Heater |
| will now be in High heat ( ) and run continuously. |
NOTE: It is normal for the Heater “fan” to run for approximately 15 seconds when the Heater shuts off after reaching the set temperature.
REMOTE CONTROL:
All the functions performed with the Remote Control work identically to the manual controls. (Figure 2)
1.Install the two “AAA” batteries supplied.
2.Do not mix old and new batteries. Do not mix alkaline, standard
3.DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.
Front View | Back View |
of Remote | of Remote |
Figure 2
If you lose your remote control, please call Customer Service to order a replacement at
Base del
Motor
Llave
Cable
Eléctrico
Conjunto de Soporte
de Columna
Figura 2
3.Arme la base enclavando las Protuberancias en los Orificios para Protuberancias. (Figura 3)
Protuberancias
Orificios
Llavepara Protuberancias
5.Alinee el Conjunto de la Base con el Conjunto de Soporte de Columna. Cerciórese de que la Muesca de Ubicación en el Conjunto de Soporte de Columna quede alineada con la Llave en el Conjunto de la Base (Figure 5). Una el Conjunto de la Base al Conjunto de Soporte de Columna con (4) tornillos M5 X 13 mm. Jale suavemente el Cable Eléctrico para que no quede holgado, y colóquelo en el Canal Para Cable del Conjunto de la Base. (Figura 6)
Muesca de
Ubicación
Llave
Figura 5
Cable Eléctrico
Conjunto de la Base 
Conjunto de
Soporte de
Columna
New 3/09 | 4 | 5394ES |
| Figura 3 | Figura 6 |
New 3/09 | 9 | 5394ES |