Methods For Attaching Mounting Bracket To Wall

PROPANE/LP GAS HEATER

INSTALLATION

Continued

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. Attach mounting bracket to wall in one of two ways

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to wall stud: This method pro- vides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to wall anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain minimum clearances shown in Figure 7. If you can, provide greater clear- ances from floor and joining wall.

2.Mark screw locations on wall (see Figure 7).

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

6 3/4"	12 1/8"
Min.
AdjoiningWall	Only Insert Mounting 14 1/2"
AdjoiningWall	Screws Through Last	Min.
	Hole On Each End	Min.
	Hole On Each End

Floor

Figure 7 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hard- ware package is provided with heater.

Attaching to Wall Stud Method

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 8.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 9). IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 8 - Folding Anchor

Figure 9 - Popping Open Anchor Wings For Thin Walls

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater (see Figure 10).

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Horizontal Slots

Stand-Out	Mounting Bracket
Tab	(attached to wall)

Figure 10 - Mounting Heater Onto Mounting Bracket

Installing Bottom Mounting Screws

1.Locate bottom mounting hole. This hole is near the bottom on the back panel of heater (see Figure 11).

2.Mark screw location on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 4 under Attaching To Wall Anchor Method. If installing bottom mounting screw into wall stud, drill hole at marked location using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacer between bottom mount- ing hole and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten screw until heater is firmly se- cured to wall. Do not over tighten. Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see page 10).

Figure 11 - Installing Bottom Mounting Screws

105563

FB-2B specifications

The Desa FB-2B is an innovative and versatile piece of technology designed to cater to a wide range of applications, particularly in industries where performance, reliability, and efficiency are paramount. This ground-breaking product incorporates cutting-edge features and technologies that set it apart from its competitors.

One of the standout features of the Desa FB-2B is its robust construction, which ensures durability and longevity, even in demanding environments. This unit is built to withstand harsh conditions, making it an ideal choice for heavy-duty applications. The materials used in its manufacturing process have been carefully selected to guarantee resistance to wear and tear, as well as potential chemical exposure.

In terms of technology, the Desa FB-2B is equipped with advanced automation capabilities. This feature allows for seamless integration into existing systems, enabling users to operate it with minimal manual intervention. The automation technology enhances overall efficiency, as it reduces human error and optimizes performance.

Another significant aspect of the Desa FB-2B is its energy efficiency. The device has been engineered to consume minimal power while delivering maximum output. Its intelligent energy management system monitors usage and adjusts performance accordingly, ensuring that energy is used effectively without compromising on productivity.

The Desa FB-2B also boasts an intuitive user interface, making it accessible for operators of all skill levels. The user-friendly design facilitates quick adjustments and monitoring, enhancing overall operational effectiveness. Additionally, the interface is equipped with real-time data analytics, providing users with insights into performance metrics that could help drive further improvements.

Safety features are paramount in the design of the Desa FB-2B. It includes multiple fail-safes and alert systems to ensure that operators are informed of any potential issues before they escalate. This emphasis on safety contributes to a more secure working environment, making it suitable for applications where human interaction is a factor.

In summary, the Desa FB-2B is a remarkable piece of equipment that combines durability, advanced technology, energy efficiency, and user-friendly design. Its features make it an exceptional choice for industries that demand high-performance solutions, ensuring that users can rely on it for their operational needs. With its focus on safety and automation, the Desa FB-2B is truly a leader in its field.