Enerco MH175KT, MH210KT, MH125KT, MH50KT Start, Stop, Description QTY, Preparing for Operation

c. Slide a small washer, spacer, small washer onto the axle next to the wheel.

d. Slide the partially assembled axle through the wheel support frame.

e. Slide the small washer, spacer, and small washer onto the axle next to the wheel support.

f.Slide the wheel then large washer onto the axle and hold in place with the remaining cotter pin.

g.Install the caps over the larger washers to finish the wheel assembly.

2.Position the heater on the wheel support frame assembly with the exit end over the wheels.

3.Use eight screws and nuts to attach the handles to the top of the tank flange. The screws will go through the handles, tank flange and wheel support frame. Install the nuts and finger tight only until all nuts are installed.

4.Tighten all the nuts.

5.Attach cord caddies to handles using No. (14) & No. (5) screws and nuts.

Handle assembly for 125KT, 175KT& 210KT only.

ITEM	PART NO.	DESCRIPTION	QTY
1	24338	Handle, Front	1
2	24338	Handle,Rear	1
3	24339	Wheel Support Frame	1
4	26977	Machine Screw Blk (long)	8
5	26037	Kep Nut Blk	12
6	28746	Axle	1
7	28752	Wheel (8’’ Dia.)	2
7	22110	Wheel (13’’ Dia. 210KT only)	2
8	28751	Cap	2
9	28748	Spacer	2
10	28747	Washer, Small	4
11	28749	Washer, Large	2
12	28750	Cotter Pin	2
13	28754	Ext. Cord Caddy	2
14	27336	Machine Screw Blk (Small)	4

PREPARING FOR OPERATION

1.Check the heater for possible shipping damage. If any is found, immediately notify the factory.

2.Follow all of the "Precautions".

3.Fill the fuel tank with clean kerosene. In extremely cold weather, condensation may develop in the tank and it is recommended that a tablespoon of de-icer be added for each gallon (4 liters) of fuel in the tank. When filling the heater, use at least 2 gallons (8 liters) of fuel. Be sure heater is level and do not overfill. Use a funnel or can with a long fill spout.

IMPORTANT: Before filling fuel tank the first time or after extended storage periods, drain the fuel tank of any moisture or condensation.

4.Locate heater at a safe distance from combustible materials. Models 50K & 75KT is not suitable for use on wood floors or other combustible materials. When used, the heater should rest on suitable insulating material at least 1 inch thick and extending 3 ft. or more beyond the heater in all directions.

START

1.50K: Plug the heater into a grounded 115V, 60 Hz, 1 Ø outlet.

75KT, 125KT, 175KT & 210KT: Turn thermostat to lowest setting, make sure “On/Off” switch is “Off”. Plug the heater into a grounded 115V, 60 Hz, 1 Ø outlet. Turn thermostat to highest setting. Start heater by push toggle switch to “On” position (light signifies switch is in “ON” position). Adjust thermostat to desired setting. Heater will cycle on/off as heat is required.

For all models: In cold weather, starting may be improved by holding a finger over the end of the pressure adjusting screw until the heater starts. This unit is equipped with an interrupt circuit. The reset is located near the power cord. If the unit does not start, press the reset button.

STOP

1.50K: Unplug heater from power source.

75KT, 125KT, 175KT & 210KT: Push “On/Off” switch to “Off” position. For extended shutdown, unplug heater from power source.

RESTART AFTER SAFETY SHUTDOWN (50K, 75KT, 125KT, 175KT & 210KT)

1.Wait 5 minutes.

2.Press reset button.

Enerco Group, Inc. Kerosene Forced Air Heater 4 Operating Instructions and Owner’s Manual