Breckwell P22I, P22FSL, P22FSA owner manual Fuel feed light is on, you have a bad control board

Page 25

TROUBLESHOOTING GUIDE

25

STOVE WILL NOT FEED PELLETS, BUT FUEL FEED LIGHT COMES ON AS DESIGNED

Possible Causes:

Possible Remedies:

 

 

1. F2 fuse on control board blew

Remove the control board. On the back there are two fuses. The

 

 

one closer to the edge is the F2 fuse. If it appears to be bad,

 

 

replace it with a 5 Amp 250 Volt fuse. Plug the stove back in and try

 

 

to run the unit.

 

 

2. High limit switch has tripped or is defective

Using the owner’s manual, locate the high limit thermodisc. There is

 

 

a red button located on the back of it. Press the red button. If you

 

 

hear a click, the high limit had tripped. The stove should now

 

 

function normally. To test if the thermodisc is bad, you can bypass it

 

 

as described previously for the POF thermodisc.

 

 

 

3.

Bad auger motor

Remove the auger motor from the auger shaft and try to run the unit.

 

 

If the motor will turn, the shaft is jammed on something. If the motor

 

 

will not turn, the motor is bad.

 

 

 

4.

Auger jam

Start by emptying the hopper. Then remove the auger motor by

 

 

removing the auger pin. Remove the auger shaft inspection plate in

 

 

the hopper so that you can see the auger shaft. Gently lift the auger

 

 

shaft straight up so that the end of the auger shaft comes up out of

 

 

the bottom auger bushing. Next, remove the two nuts that hold the

 

 

top auger biscuit in. Then rotate the bottom end of the auger shaft

 

 

up towards you until you can lift the shaft out of the stove. After you

 

 

have removed the shaft, inspect it for bent flights, burrs, or broken

 

 

welds. Remove any foreign material that might have caused the

 

 

jam. Also, check the auger tube for signs of damage such as burrs,

 

 

rough spots, or grooves cut into the metal that could have caused a

 

 

jam.

 

 

5. Loose wire or connector

Check all wires and connectors that connector to the auger motor,

 

 

high limit switch, and the Molex connector.

 

 

 

6.

Bad control board

If the F2 fuse is good, the wires and connectors check out good, and

 

 

the high limit switch did not trip, test for power going to the auger

 

 

motor. If there is not a full current going to the auger motor when

 

 

the fuel feed light is on, you have a bad control board.

 

 

 

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Economy Series P22 Important Information IntroductionSafety Precautions Table of Contents Specifications InstallationPreparation ClearancesCombustion AIR Supply When Outside AIR is not UsedVenting Equivalent Vent Length EVL Freestanding InstallationsAssembling Pedestal or LEG SET Horizontally Through Wall refer to FigureVertically Into Existing Chimney System Vertically with NEW Chimney System Refer to FigureVertically Into Existing Masonry Fireplace Installation Through Side of Masonry ChimneyAssembling the Flashing SET Insert InstallationsWhen Vent Pipe Extends to Chimney TOP Refer to Figures 16 AS a BUILT-IN Fireplace Chase dimensions shown are minimums and must be maintainedInstallation in to a Factory Built Metal Fireplace Electrical InstallationSpecial Mobile Home Requirements Proper Fuel OperationPRE-START-UP Check Building a FireRoom AIR FAN Opening DoorRE-STARTING a Warm Stove Shutdown Procedure Breckwell Maintenance ToolSafety Features If Stove Runs OUT of PelletsThermostat Installation Thermostat InstallationOptional Thermostat Please Read this Cleaning MaintenanceASH Removal ASH DisposalBlowers Disconnect Power Before Servicing UnitDaily Weekly Bi-Annually Annually or per Ton Chimney CleaningStove Shuts OFF and the # 2 Light Flashes Troubleshooting GuidePossible Causes Stove Shuts OFF and the # 3 Light Flashes Possible Causes Possible Remedies Stove Feeds PELLETS, but will not IgniteSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onFuel feed light is on, you have a bad control board Troubleshooting Guide Heat Level Setting P22 High Limit Switch Keeps TrippingSmoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram IGN Replacement Parts
Related manuals
Manual 30 pages 55.5 Kb

P22FSA, P22FSL, P22I specifications

Breckwell has established itself as a key player in the realm of pellet stoves, with its P22 series being a testament to its commitment to innovation, efficiency, and user comfort. The P22I, P22FSL, and P22FSA models each boast unique features, yet all are designed with the same high-quality standards that Breckwell is known for.

The Breckwell P22I is an Intelligent pellet stove that stands out for its sleek design and exceptional heating capacity. It delivers up to 50,000 BTUs, making it suitable for larger spaces while ensuring efficient heat distribution. One of its main features is the intuitive digital control board with advanced programming options, allowing users to set their desired temperature and heating schedules effortlessly. The P22I also supports an optional direct vent system, increasing safety by minimizing the risk of backdrafts and ensuring proper exhaust flow.

The P22FSL model showcases a more modern aesthetic with its large viewing window, allowing users to enjoy the mesmerizing flames of the fire while heating their homes. Its side-loading feature offers convenience when it comes to refilling pellets. The P22FSL also incorporates a powerful blower to enhance heat circulation throughout the room. Furthermore, it features an adjustable heat output, providing users with the ability to customize their heating experience based on their preferences.

For those seeking a more traditional look, the P22FSA provides a classic yet efficient design. This model is perfect for homes that emphasize a more rustic charm while still delivering all the benefits of a modern pellet stove. Like its counterparts, the P22FSA provides robust heating capabilities of up to 50,000 BTUs. It also features a simple control panel, making it accessible for users of all technical backgrounds.

All three models utilize a reliable feed system that ensures a consistent flow of pellets, allowing for prolonged operational time before needing a refill. Additionally, they are equipped with safety features such as a thermal sensor and automatic shut-off to prevent overheating, offering peace of mind for users.

In terms of efficiency, the P22 series meets stringent EPA standards, making them environmentally friendly options for home heating. The use of premium materials in their construction ensures durability and longevity, making them a wise investment for homeowners looking to combine comfort with sustainability. Overall, the Breckwell P22I, P22FSL, and P22FSA models reflect the brand’s dedication to quality, comfort, and innovation in the pellet stove market.
Top Page Image Contents