1. Fill Base with water and add 1/3 teaspoon of bleach. Let solution remain for 20 minutes, stirring every few minutes to ensure that all surfaces are coated.
2. Empty Base after 20 minutes. Rinse with water until bleach smell is gone. Dry with clean cloth or paper towel.
3. Wipe all exterior surfaces of the Fan Housing with a soft, dry cloth.
DO NOT USE WATER TO CLEAN THE FAN HOUSING. AN ELECTRIC SHOCK MAY RESULT OR THE HUMIDIFIER MAY BE DAMAGED. DO NOT IMMERSE OR SPRAY ANY PART OF THE HUMIDIFIER WITH WATER.
4. Replace the Wicking Filter into the Base, being careful not to damage the Filter. NOTE: Do not wash the Wicking Filter, since this will damage the Wicking Filter.
Fill the Water Tank and replace Tank on Base.
5. Fill Base with undiluted white vinegar. Let solution stand for 20 minutes.
6. Dampen soft, clean cloth or sponge with undiluted white vinegar and wipe out Base to remove scale. DO NOT use soap, detergents or abrasive cleaners.
7. Rinse thoroughly in clean warm water to remove scale and vinegar before disinfecting the Base.
Disinfecting Base
Turn switch to the OFF (O) position and unplug the cord from wall outlet.
Remove Tank & Fan Housing and place on a flat surface. Remove the Wicking Filter from the Base by carefully lifting straight up, without bending, breaking or tearing the Wicking Filter.
3.
4.
Weekly Maintenance—Removing Scale
1. Empty any remaining water from the Base and Tank. Reassemble Humidifier.
2. Turn switch on and operate the Humidifier without water until the Wicking Filter is thoroughly dry.
Replace Wick, Fan Housing, then the Tank. Humidifier is now ready for use.
3.
Care and Cleaning
CAUTION: ALWAYS TURN OFF THE POWER SWITCH AND DISCONNECT THE POWER CORD FROM THE ELECTRICAL OUTLET BEFORE CLEANING.
Humidifiers provide comfort by adding moisture to dry indoor air. For maximized benefit from your Vicks Humidifier, follow instructions carefully. Please note that this is an electric appliance and requires careful attention when in use.
Tap water may contain pollutants and minerals (scale) that can deposit on the inner surfaces of the Humidifier and clog the Wicking Filter. Such scale can accelerate the growth of microorganisms and can impair the performance of the Filter.
Daily Maintenance
1. Turn switch to off (O) position and unplug the cord from wall outlet.
2. Remove Tank & Fan Housing and empty Base. Rinse Base and Tank, wipe clean, and dry with a clean cloth or paper towel. Be careful that you do not damage the delicate Wicking Filter. DO NOT immerse the Fan Housing or clean with water.
Using Your Vicks® Humidifier (Model V3600)
Your Vicks Humidifier comes fully assembled and ready to use.
First Time Use
Read all instructions before using this appliance. With proper care and maintenance, the humidifier should be able to provide at least 12 - 24 hours operation per filling.
Unpack and remove all packing material from the Water Tank and Base. Completely unravel power cord and place unit on a flat, stable surface at least 5 - 12 inches away from walls and heat sources. Do not use product if cord has been damaged. Place cord out of the way where it cannot be pulled or stepped on. Follow the directions below to fill and operate the Humidifier.
Filling the Water Tank
Always UNPLUG the humidifier before filling.
1. Remove the Water Tank from the Base and turn it upside down. Turn the Tank Cap counterclockwise to open.
2. Fill the Water Tank with clean, cool, tap water and replace the Tank Cap by firmly turning clockwise. Turn the tank upright and check Tank Cap for leaks. If any water drips from Tank Cap, remove it and re-tighten. Make sure the circular rub cap Gasket (o-Ring) is in place when replacing Tank Cap — this prevents water leakage.
Carry Water Tank using one hand on the handle and one on the bottom of the Tank.
Be sure the Water Tray and Wicking Filter are in place.
Replace the Water Tank on the Base by aligning the Tank Cap into the Water Tray.
Caution:
Do not use hot water, which may damage the wick.
Do not add any medication or other additives to the water.
Do not pour any water into the outlet.
Operating Instructions
1.
2. Make sure that power switch is in OFF (O) position, place the unit on a flat, stable surface and plug cord into a 120 VAC wall outlet.
CAUTION: DO NOT PLUG IN THE CORD WITH WET HANDS; ELECTRIC SHOCK COULD RESULT.
3. Turn switch to desired speed. Fan will start turning. Green Power Indicator Light will illuminate.
4. Use the humidistat switch to select the humidity level you desire. To increase humidity turn knob clockwise. When desired humidity level is reached, the humidifier will shut off and the “desired humidity” light will come on. The humidistat will automatically turn the humidifer back on and off again to maintain the humidity level, with the desired humidity light indicating accordingly.