Testing Your Smoke Alarm | Firex 110-1011E guide

Testing Your Smoke Alarm cont.

The center test button accurately tests all functions. NEVER use an open flame from a match or lighter to test this smoke alarm. You may ignite and set fire to the smoke alarm and your home.

Test all smoke alarms weekly as follows:

1.Look at the LED power indicator. A visual light flashing about once a minute indicates the smoke alarm is receiving battery power. See “LED Power/Alarm Indicator” chart.

2.Firmly depress the test button for at least five (5) seconds [ten (10) seconds for Model CCPB]. The smoke alarm will sound its alarm horn loudly. The alarm may sound for up to 10 seconds after releasing the test button.

3.If smoke alarm does not sound, replace the smoke alarm immediately. If the smoke alarm is under warranty, see warranty information at the end of this manual for more information.

REPLACE OR RETURN THE ALARM IF THE PUSH-TO-TEST FUNCTION DOES NOT OPERATE PROPERLY AFTER FOLLOWING THE PROCEDURES OUTLINED ABOVE (see REPAIR on page 5).

LED Power/Alarm Indicator

The visual LED indicates the following:

Blinks once a minute

Normal operation–smoke alarm is receiving battery power

Blinks once a second

Smoke is detected; audible alarm will simultaneously sound

Models CC, CEC, CPBC and CCPB only:

Blinks once every 10 seconds

Alarm Control (Quick-Quiet™) is actively quieting an unwant- ed alarm

Special Features of Model CC, CEC, CCPB and CPBC

Alarm Control (Quick-Quiet™) (Models CC, CEC CCPB, and CPBC only)

When activated, Alarm Control (Quick-Quiet™) quiets unwanted alarms for a maximum of 15 minutes. Always check that the smoke alarm has activated in a false alarm situation. Be sure a real fire emergency does not exist.

To use the Alarm Control (Quick-Quiet™) feature:

Press and release the test button during an unwanted alarm. The alarm should stop within ten seconds. The LED will flash about once every 10 seconds. This means the smoke alarm is in Alarm Control (Quick-Quiet™) mode.

If the smoke alarm does not go into Alarm Control (Quick-Quiet™) and continues to sound its loud alarm horn, or if it initially goes into Alarm Control (Quick-Quiet™) then resounds the alarm, the smoke is very heavy. This is possibly a dangerous situation—-take emergency action immediately.

Safety Light (Model CEC only)

Model CEC features a Safety Light. This light turns on when the smoke alarm sounds. The Safety Light is a miniature lamp which will last up to 15 hours of continuous operation. Its purpose is to assist in pro- viding light in the escape route during a fire.

If the Safety Light does not turn on when the smoke alarm is tested, check the batteries. Replace the batteries if necessary.

IMPORTANT: Smoke alarms with the Safety Light require two (2) AA batteries to operate the Safety Light. These batteries are in addition to the 9-volt battery used to operate the smoke alarm.

Chamber Test Feature (Models CCPB and CPBC only)

Once a minute Models CCPB and CPBC perform a chamber test. If at any time the unit chirps and the LED does not flash–see MAINTENANCE AND CLEANING section of this manual.

Battery Replacement

Replace battery at least once a year or immediately when the low battery signal (a chirp) sounds once a minute. Use only the following batteries as replacements in this smoke alarm: Eveready 522 and 1222 (except Model CCPB), or Duracell MN 1604. Long Life Lithium replacement battery is Ultralife U9VL-J.

NOTE: For Model CEC, replace Safety Light batteries with two AA size batteries. Replace all batteries at the same time.

!WARNING

DO NOT USE ANY OTHER TYPE OF BATTERY, EXCEPT AS SPECIFIED IN THIS MANUAL. DO NOT USE RECHARGEABLE BATTERIES.

1.Turn smoke alarm counter-clockwise to detach from mounting plate.

2.From back of smoke alarm, lift tab to open battery pocket door (Models CB, CC and CPBC only). Remove battery from pocket. Disconnect and discard drained battery from battery connector.

3.Connect a fresh, 9-volt battery to connector. The battery will fit only one way. Be sure battery con- nector is securely attached to battery terminals.

NOTE: For Model CEC, replace Safety Light batteries with two AA size batteries. Replace all batteries at the same time.

4.Push test button for at least five (5) seconds [ten (10) seconds for Model CCPB]. The alarm horn should sound. This means the battery is connected properly.

5.Place battery into battery pocket. Close battery pocket door. Push down until it snaps into place.

6.Reattach smoke alarm to mounting plate. To do so, turn smoke alarm clockwise until it snaps into mounting plate.

7.Test smoke alarm using test button as described on page 3, TESTING YOUR SMOKE ALARM.

Maintenance and Cleaning

In addition to weekly testing, this smoke alarm requires yearly battery replacement, and periodic cleaning to remove dust, dirt, and debris. Long Life Lithium battery can be expected to last as long as five (5) years, but is warrantied for one (1).

Cleaning

Clean the smoke alarm at least once a month to remove dust, dirt, or debris as follows:

•Using the wand attachment of a vacuum cleaner, vacuum all sides and cover of smoke alarm. Be sure all the vents are free of debris.

•If necessary, remove battery and use a damp cloth to clean smoke alarm cover.

IMPORTANT: Do not attempt to remove the cover or clean inside the smoke alarm. THIS WILL VOID YOUR WARRANTY.

110-1011E specifications

The Firex 110-1011E is a highly regarded smoke alarm that emphasizes safety and reliability in residential settings. As a vital component of any home safety system, this device integrates advanced technologies to enhance its performance and user-friendliness.

One of the standout features of the Firex 110-1011E is its use of an ionization sensing technology. This technology is particularly effective at detecting fast-flaming fires, making it an essential tool for early smoke detection. The ionization sensor works by employing a small amount of radioactive material, which helps in creating a current between two electrodes. When smoke enters the sensing chamber, it disrupts this current, triggering the alarm, thus providing timely warnings when it matters most.

In addition to its superior sensor technology, the Firex 110-1011E boasts a unique battery backup feature. This ensures that the alarm remains operational even during power outages, a crucial aspect during emergencies when electricity might be compromised. The device is powered by a 9-volt battery, which is easy to replace and maintain.

Another key characteristic of the Firex 110-1011E is its user-friendly design. The alarm features a simple test button that allows homeowners to check the functionality of the unit regularly. This promotes proactive maintenance, ensuring that the device operates efficiently when needed. Furthermore, the alarm comes equipped with a loud 85-decibel alarm that is designed to be heard easily throughout the home, providing an effective warning to occupants.

The Firex 110-1011E is also designed with the homeowner’s peace of mind in mind. It includes a low battery warning feature, which signals when the battery needs replacement, reducing the risk of the alarm being non-operative due to a dead battery. Its compact design ensures it can be easily installed in various locations within a home, from hallways to bedrooms.

In summary, the Firex 110-1011E smoke alarm is a high-performance device that combines advanced ionization sensing technology with practical features like battery backup and user-friendly operation. Its reliable design makes it an invaluable addition to any household’s safety measures, ensuring protection against the dangers of fire. Investing in the Firex 110-1011E means prioritizing safety and taking a proactive approach to fire prevention.