Kidde 0916, 440375 manual Locations to Avoid, Installation Instructions, Operation and Testing

Page 3

WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER R.V. OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE, BEFORE EACH TRIP AND AT LEAST ONCE A WEEK DURING USE.

2. LOCATIONS TO AVOID

In the garage. Products of combustion are present when you start your automobile.

Less than 4” (10cm) from the peak of an “A” frame type ceiling.

In an area where the temperature may fall below 40ºF or rise above 100ºF.

In dusty areas. Dust particles may cause nuisance alarm or failure to alarm.

In very humid areas. Moisture or steam can cause nuisance alarms.

In insect-infested areas.

Smoke alarms should not be installed within 3 ft (.9m) of the following: the door to a kitchen, the door to a bathroom containing a tub or shower, forced air ducts used for heating or cooling, ceiling or whole house ventilating fans, or other high air flow areas.

Kitchens. Normal cooking may cause nuisance alarms. If a kitchen alarm is desired, it should have an alarm silence feature or be a photoelectric type.

Near fluorescent lights. Electronic “noise” may cause nuisance alarms.

3. INSTALLATION INSTRUCTIONS

CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE!

2.To insure aesthetic alignment of the alarm with the hallway or wall, the “A” line on the mounting plate must be parallel with the hallway when ceiling mounting or hori- zontal when wall mounting.

3.After selecting the proper smoke alarm location as described in Section 1, attach the mounting plate to the ceiling as shown in Figure 1. For wall mounting see Figure 2. Place mounting plate on the wall. Be sure the “UP FOR WALL MOUNT- ING “ text and arrow are facing up. Use the screws and anchors provided to secure the mounting plate (use 3/16” drill bit for anchors).

4.Battery installation instructions are provided on the inside of the battery door. To ensure proper installation of the smoke alarm battery, follow the instructions.

5.When installing the battery, press the battery reminder finger down into the battery compartment and install the battery (see Figure 3).

CAUTION! IF THE BATTERY REMINDER FINGER IS NOT HELD DOWN IN THE BATTERY COMPARTMENT BY THE BATTERY, THE BATTERY DOOR WILL NOT CLOSE AND THE UNIT WILL NOT ATTACH TO TO THE MOUNTING BRACKET.

6.Alignment marks are provided on the edge of the trim plate and the alarm. After installing the mounting plate, place the alarm

on the mounting plate with the alignment marks lined up. Twist the alarm in the direc- tion indicated by the “ON” arrow on the alarm cover (see Figure 4) until it locks in place.

7.USING TAMPER RESIST LOCKING PIN: To

make your smoke alarm somewhat tamper

FIGURE 5 Tamper Resist

resistant, a locking pin has been provided in

When mounting in a hallway, the “A” line should be parallel with the hallway.

When wall mounting, the “A” line should be horizontal and the “UP FOR WALL MOUNTING” arrow must be pointing up.

Locking Pin

the bag with the screws and anchors. Using

this pin will deter children and others from removing the alarm from the mounting plate. To use the pin, insert it into the hole in the side of the alarm after the alarm has been installed on the mounting plate (see Figure 5).

NOTE: THE TAMPER RESIST PIN WILL HAVE TO BE REMOVED IN ORDER TO CHANGE THE BATTERY. USE A LONG NOSE PLIERS TO PULL THE PIN OUT OF THE HOLE. IT IS NOW POSSIBLE TO REMOVE THE ALARM FROM THE

FIGURE 1

FIGURE 2

Alignment Marks

InstallRemove

FIGURE 3

FIGURE 4

1.Remove the mounting plate from the back of the alarm by holding the mounting plate and twisting the alarm in the direction indicated by the “OFF” arrow on the alarm cover.

MOUNTING PLATE.

8.After installation, test your alarm by depressing and holding down the test button for several seconds. This should sound the alarm.

4. OPERATION AND TESTING

OPERATION: The smoke alarm is operating once a fresh battery is installed and test- ing is complete. When products of combustion are sensed, the unit sounds a loud 85db pulsating alarm until the air is cleared.

HUSH CONTROL: The “HUSH” feature has the capability of temporarily desensitizing the alarm circuit for approximately 7 minutes. This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. The smoke alarm is desensitized by pushing the “HUSH” button on the smoke alarm cover. If the smoke is not too dense, the alarm will silence immediately and “chirp” every 30 -40 seconds for approximately 7 minutes. This indicates that the alarm is in a temporarily desensitized condition. The smoke alarm will automatically reset after approximately 7 minutes and sound the alarm if particles of combustion are still pres-

Image 3
Contents DC3 Recommended Locations for Alarms Contents of this ManualMobile Home Installation Installation Instructions Operation and TestingLocations to Avoid Battery Replacement Nuisance AlarmsMaintenance Limitations of Smoke AlarmsNfpa Required Protection Good Safety HabitsWhat to do When the Alarm Sounds NRC InformationFive Year Limited Warranty Service and Warranty

0916, 440375 specifications

The Kidde 440375,0916 is a highly regarded smoke and carbon monoxide detector that combines advanced technology with user-friendly features, ensuring the safety of your home and loved ones. This device is designed to provide continuous monitoring of both smoke and carbon monoxide levels, providing crucial alerts in case of danger.

One of the standout features of the Kidde 440375,0916 is its dual detection capability. This model integrates a photoelectric smoke sensor, which is particularly effective at detecting smoldering fires that may produce large amounts of smoke without producing significant flames. This technology can lead to faster response times and a higher likelihood of escaping a dangerous situation.

In addition to smoke detection, this unit also includes a reliable electrochemical sensor for carbon monoxide detection. Carbon monoxide is a colorless, odorless gas that can be deadly in low concentrations, and the inclusion of this feature makes the Kidde 440375,0916 a critical addition to any home safety strategy. The electrochemical sensor is known for its accuracy and sensitivity, ensuring that even low levels of CO are detected promptly.

Another significant characteristic of the Kidde 440375,0916 is its user-friendly design. The unit includes a large digital display, providing clear visibility of current conditions and alerts. The display shows the levels of smoke and carbon monoxide, allowing users to gauge their environment easily. Additionally, this model features voice alerts that announce the type of danger present, whether it’s smoke or carbon monoxide, providing clarity in moments of panic.

The Kidde 440375,0916 also emphasizes ease of installation and maintenance. It is designed to be easily mounted on walls or ceilings, making it a versatile option for any room in the house. The unit comes equipped with a battery backup system, ensuring continued operation during power outages. Regular maintenance is made simple with a test/reset button, allowing users to regularly check the functionality of the device.

In conclusion, the Kidde 440375,0916 is a premium smoke and carbon monoxide detector that prioritizes safety through advanced detection technologies, user-friendly design, and reliable performance. It stands out as an essential tool for home safety, offering peace of mind to families and individuals alike. By including features aimed at enhancing user experience and ensuring prompt alerts, the Kidde 440375,0916 represents an excellent choice for comprehensive home protection.