Maintenance, Installation and Operation

Operating Instructions and Parts Manual

Installation and Operation (Continued)

Do not handle pump with wet hands or when standing in

water or on a damp surface when the unit is operating or fails to operate. Always disconnect pump power cord from power source before handling.

6.Plug the power cord into a ground- ed 115-volt AC power outlet. The pump will start operating as soon as the power cord is plugged into the power outlet.

7.The pump will remove water down to 1/8 inches of the hard surface the pump was placed on.

8.The pump should be turned off once the water level reaches the 1/8-inch mark.

Do not allow pump to run dry.

The shaft seal depends on water for

operate, unplug power cord and proceed to maintenance guide- line item 4 in this section.

3.Verify discharge hose is correctly installed.

a.Connect hose to another water source such as a faucet. If water flows through hose, proceed to step 3b. If water is restricted, ver- ify discharge hose is unwound. Remove all kinks, bends or obstructions in hose.

b.Verify pumping height does NOT exceed 25 feet (See Figure 1). If pumping height is greater than 25 feet, this pump will NOT work.

4.Periodic cleaning of pump is required to maintain performance of the pump. Follow the cleaning steps listed below:

a.Unplug the power cord.

f.Replace the gasket making sure the openings are aligned.

g.Replace the volute cover.

h.Replace the 3 screws.

lubrication. Operating pump without water will damage the shaft seal and cause pump failure.

Maintenance

Always disconnect electric supply before attempting to install, service, relocate or per-

form any maintenance. Failure to do so could result in fatal electrical shock.

Minimal service is required for this pump. If pump should fail to operate, perform the following troubleshooting guidelines:

1.The motor housing of the pump is completely sealed and requires no service.

Disassembly of the motor

housing or alteration of the power cord could result in fatal electrical shock.

2.Verify pump is operating correctly.

a.Disconnect pump from power source.

b.Disconnect discharge hose from pump.

c.Immerse pump in a bucket or tub of water.

d.Plug power cord into a grounded 115 volt AC power outlet. If pump operates correctly proceed to step #3. If pump does NOT

b. Remove the 3 screws at the bot- tom of the pump.

c. Remove the volute cover. Note the alignment marks.

d. Remove the gasket. Note how the openings in the gasket align with the openings in the pump base.

e. Remove the debris and make sure the impeller turns freely.

25 Ft. Max.

Water Level

Figure 1 Water Level

TSC, 351301-001 specifications

Wayne TSC, model 351301-001, is a state-of-the-art fuel dispenser designed to meet the demands of modern retail fueling operations. Known for its reliability and advanced technology, the Wayne TSC series combines user-friendly features with high-end performance, making it an ideal choice for gas stations looking to enhance their service offerings.

One of the primary features of the Wayne TSC, 351301-001 is its dual-hose capability, allowing for simultaneous dispensing of different fuel types. This is particularly beneficial for stations that provide both gasoline and diesel, as it enables quicker service and reduces the waiting time for customers.

Equipped with a robust and intuitive user interface, the Wayne TSC 351301-001 ensures that customers can easily navigate through the fueling process. The bright, backlit display provides clear visibility, even in low-light conditions, ensuring an enhanced user experience. Furthermore, the dispenser supports various payment options, including credit and debit cards, mobile payment solutions, and loyalty card integration, catering to the diverse preferences of customers.

In terms of technology, the Wayne TSC, 351301-001 incorporates advanced fuel management systems that enhance accuracy in fuel measurement and help in tracking sales in real-time. The unit is designed with advanced leak detection technology, ensuring compliance with environmental regulations and safeguarding against fuel loss. This feature not only protects the environment but also reduces operational costs for station owners.

Durability is another hallmark of the Wayne TSC series. Built with high-quality materials, the 351301-001 is resistant to harsh weather conditions, thereby prolonging its lifespan and minimizing maintenance needs. The dispenser's modular design simplifies repairs and upgrades, ensuring that service stations can continue to operate efficiently even in the face of wear and tear.

Additionally, the Wayne TSC, 351301-001 is energy-efficient, with low power consumption design elements that contribute to sustainability efforts within the fueling industry. This dispenser aligns with the growing trend of eco-conscious operations, making it an appealing choice for forward-thinking gas stations.

In summary, the Wayne TSC, model 351301-001 stands out in the competitive landscape of fuel dispensers. Its combination of user-friendly features, advanced technology, durability, and energy efficiency makes it a leading option for retailers looking to modernize their fueling operations while enhancing customer satisfaction.