Installation / Operation / Electrical

PUMP INSTALLATION

Set the pump on the bottom of the sump, making sure that

it sits solidly and is level. Be sure there is enough space

around the punlp to allow the switch frec mo_ cnlcnt ;is the

stimp water level changes. Du Rot iitstall the ptimp on clay, earth, or sand surlTace.

I _" CAUTION IRisk

.I of flooding. If a flexible discharge

hose is used, pump may move around in sump when

niotor starts. If it moves far enough so that tile switch hits the side of the sump, the switch may stick and prevent pump from starting. Make sure that pump is secured so that it cannot walk arotmd in sump.

Hose Kit No. 27909 can be used as the discharge pipe. Run the discharge pipe to the nearest sewer outlet or other point of disposal. Use the most direct route and the fewest turns and elbows possible.

Use Teflon tape to seal threads in plastic pipe. Hand tighten only.

NOTE: To avoid backflow into sump when pump shuts off, install a Check Valve, SEARS Stock No. 2789, in threaded dis- charge port of pump. A SEARS No. 2789 Check Valve is con- structed with an anti-aiflock hole. If you use a SEARS No. 2792 or any other check valve, drill a 1/8" hole in the discharge pipe

just above the pump discharge port and below the Check Valve to prevent pump from airlocking.

Make sure the air-bleed hole is down inside the sump so that it does not run water on the basement floor when the pump is mnning.

AUTOMATIC FLOAT SWITCH

INSTALLATION AND OPERATION

Your SEARS Model 390.305001 Submersible Drainer comes

with the automatic float switch mounted on the motor hous-

ing ready for operation. Tether length is factory set at 3"

(76mm). Do not change tether length. See Page 6 for verti- cal float switch instructions.

I AWARNING_ Risk of electric shock. Always disconnect

the pump and switch from the electrical power source

before doing any maintenance!

Follow instructions below to install pump with factory

mounted switch:

1.Be sure automatic float can swing freely through its entire

arc without interference from pump, piping, sump wall or any other object.

2.Plug the automatic switch cord into a properly grounded

outlet (see "Electrical Connections", Page 4). Plug the pump power cord into the back of the switch plug.

3.Test the installation by adding water to the sump pit until

pump operates normally as follows:

A.When sump is dry, the watertight automatic float

switch is hanging in a downward position and the pump is off.

B. As water

comes

into

the

sump,

tile

auton/atic

float

switch

rises

upward

position

and

the

pump starts.

(7. Water

will

contint_e to

pumped

until

the

float

switch

hanging

ill

the

dox_nward

position

agaiit,

when

pump

will

stop.

DO NOT ALLOW PUMP TO RUN DRY!

sure

leave

at least

(127mm)

of water

above

pump

base

plate

when

pump

stops.

Running

pump

dry

could

ruin

the

pump

and

will

void

the

warranty.

Figure 2

Switch tether is factor), set at 3" (76mm).

NOTICE: Do not change tether length.

ELECTRICAL CONNECTIONS

The Sump Pump has a 3-prong electric plug. The third prong is used to ground the pump to prevent possible fatal shock.

The third prong should never be removed. Your electrical

outlet should be the 3-prong, polarized type with an inter- nal ground.

An individual branch 15 amp electrical circuit is recom-

mended. DO NOT USE AN EXTENSION CORD.

Testing for Ground

For your safety, check your outlet for ground using an

Underwriters Laboratory Listed Circuit Analyzer (Figure 3A). A Circuit Analyzer will tell you by a pattern of lights if the

power, neutral, and ground wires are correctly connected

to your outlet. It can also be used to check other outlets in

your home. A Circuit Analyzer is available in the Sears Electrical Department.

UL Listed

Figure 3A

665 0194