Mounting L6008A Remote Bulb Controller

M8970A

Fig. 12. Bulb support.

3.Break the holder to the desired length. (See Fig. 13).

NOTE: The holder must be long enough to hold the sensing bulb in freely circulating air away from the duct wall. Neatly coil the excess capillary at the controller case or at the bulb holder.

M7216A

Fig. 13. Removing excess bulb support.

PINCH TOP EDGES OF

HOLDER TOGETHER

AT EACH SEGMENT

CAPILLARY

TUBING

SENSING

BULB

BE SURE EXTENSION TUBE IS
UNDER BULB HOLDER, AS SHOWN	M7217A

Fig. 14. Securing capillary in bulb holder.

4.Place the capillary in the bulb holder channel. Pinch the top edges of the holder together at each segment. (See Fig. 14).

5.Insert the bulb holder into the controlled area through the hole prepared in step 1.

6.Fasten the bulb holder to the duct wall with the screws provided.

L4006,7,8; L6006,7,8 AQUASTAT® CONTROLLERS

Mounting Remote Bulb Models

For Outdoor Air Sensing

These models have a 5 ft (1.5 m) capillary that establishes the maximum distance between the case and the outdoor mounting.

Install the bulb on the outside of the building in the shield provided (See Fig. 15) where it can be exposed to representative air temperature, but not to direct sunlight. Mount the bulb high enough so that accumulated snow, leaves, or other debris cannot obstruct circulation of air around it, and where children cannot reach it. Avoid vents from the building.

Install the case at the indoor location selected, fastening the screws through holes in the back of the case. Bring out the bulb and tubing through a 3/4 in. (19 mm) hole in the outside wall, avoiding sharp bends or kinks. Leave excess tubing coiled near the case. Do not make sharp bends near the case or bulb.

Slip the bulb through the supports in the shield. Pinch the split supporting clip until it holds the bulb firmly in position. If the seal-off tube protrudes from under the shield, bend it under as shown in Fig. 15.

Hold the shield over the mounting position and form a small- radius bend in the tubing. Place the split plug around the tubing and move the shield into the mounting location as a unit. Push the split plug into the hole until it is wedged securely in place. Fasten the shield in place on the wall with the screws provided.

NOTE: If the tubing is properly shaped and the split plug installed as directed, the shield will cover the split plug, and the hole in the wall will be hidden from sight.

SPLIT WOOD PLUG

3/4 IN.

	INSERT BULB	(19 MM)
	IN CLAMP	(19 MM)
	IN CLAMP	HOLE IN
		HOLE IN
		WALL
	OUTDOOR
	SENSING
	BULB
		CAPILLARY
		TUBING
		SEAL-OFF
		TUBE
	34886A
	BULB
	SHIELD	M8800A

Fig. 15. Mounting bulb in shield outside building.

Mounting L6008A Remote Bulb Controller

Mounting with Guard Bracket

Mount the bulb in the guard bracket as shown in Fig. 16. Locate the bulb and bracket combination, in freely circulating air, in the controlled area. With screws provided, fasten the bracket in place.

11	60-2104—10

L6006, L4008, L6008, L6007, L4007 specifications

Honeywell has long been a leader in the field of heating, ventilation, and air conditioning (HVAC) controls, and its range of controls including the L4007, L6007, L6008, L4008, and L6006 models exemplifies this commitment to innovation, reliability, and energy efficiency.

The L4007 series is designed primarily for low-pressure applications, providing accurate control over gas and oil burners. With features such as adjustable differential settings, this series ensures that the heating systems operate optimally, enhancing both performance and safety. The robust construction and weather resistance make the L4007 an ideal choice for a variety of heating applications.

In contrast, the L6007 series takes it a step further by incorporating advanced technologies for more complex heating systems. These thermostats offer features like dual setpoint capabilities, temperature calibration, and improved diagnostics. They are particularly suited for commercial applications, where precision is essential for maintaining comfortable environments.

The L6008 expands on these features by introducing programmable capabilities. Users can tailor their heating needs according to specific schedules, leading to more efficient energy use. This model incorporates smart technology, allowing for integration with other smart home devices, which adds an extra layer of convenience for homeowners.

For those requiring more comprehensive control, the L4008 offers superior compatibility and flexibility. This model can manage multiple stages of heating or cooling and is perfect for systems that demand high degrees of control. With built-in protections against overheating and malfunction, the L4008 ensures a safe operation for all heating systems.

The L6006 offers a unique solution for applications that require both heating and cooling capabilities. This model is designed for versatility, making it suitable for a range of environments, from residential to commercial. Its user-friendly interface and precise control settings simplify the operation and management of HVAC systems.

Overall, Honeywell’s L4007, L6007, L6008, L4008, and L6006 models reflect the brand's dedication to providing high-quality, reliable, and efficient control solutions for diverse heating and cooling needs. They are engineered with advanced technologies that prioritize user comfort, energy efficiency, and system protection, making them essential tools for modern HVAC applications.