LG Electronics LT1430CR owner manual Procedure B, Top View, Fasten the screws

Page 14

Installation

PROCEDURE B

1 Redirect the louvers at the back of the wall sleeve to 60° angle as shown in the FIG 8. The use of pliers is recommended.

 

7 3/32"

60°

60°

 

Rear Louvers

 

(Top View)

 

FIG. 8

2

If the wall sleeve already has a rear grille, skip

 

to step 4. If the wall sleeve does not have a rear

grille or louvered panel, install the plastic grille from the kit. Cut the plastic grille to 25-1/2" wide and 15-1/4" high. Place the plastic grille to the inside of the wall sleeve at the rear flange.

4

Remove the backing from the Vertical Insulation

 

strip 159/16 x 13/8 x 13/8 and attach that to the

inside right of the sleeve as shown below. Remove the backing from the Around Insulation strip 671/8 x 13/8 x 25/32 and attach that to the inside front of the sleeve as shown below.

Indoor

Outdoor

Around Insulation

 

Vertical Insulation

 

9 1/2"

6"

 

FIG. 11

Place the plastic grille

FIG. 9

 

 

3

Fasten the 4 washer screws to secure the grille

 

to the wall sleeve. If you need plastic nuts to

5 If the depth of your existing wall sleeve is less than or equal to 18", skip to step 6. Otherwise, cut the baffles and the support blocks according to length "A" in the table below.

mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of the rear flanges.

 

or

Fasten the screws

FIG. 10

 

Depth"D" of the existing

Length "A"

wall sleeve (inches)

(inches)

 

 

 

18 D

18-5/8

3/4

18-5/8

D 19-3/4

1-3/4

19-3/4

D 22

4

 

 

 

A

Support

Block

Baffle

A FIG. 12

14Room Air Conditioner

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Room AIR Conditioner Table of Contents Outlet Power cord length Is damaged Safety PrecautionsDon’t use a power cord, a Always plug into a grounded Be caution when unpacking and installingCome from it During operation Unplug the unit if strangeSounds, odors, or smoke Ventilate the room well whenOtherwise, it may cause vibration or water leakage Hold the plug by the head When gas leaks, openKeep level parallel in installing the product It will cause electric shock or fireDo not step on Always insert the filter Sharp edges when Perform ventilation Installing SometimesDo not block the inlet or outlet of air flow Be cautious not to touchBefore Operation Cleaning and MaintenanceService Preparing for OperationIntroduction Symbols Used in this ManualFeatures Electrical Data Electrical SafetyUse Wall Receptacle Power Supply Wash hands after handlingElectrical Safety Please Read CarefullyMake sure air conditioner does not fall during installation InstallationInstallation Requirements Installation HOW to InstallTo the wall sleeve. If you need plastic nuts to Procedure aSupplied with your unit,skip to step Trim 2 eaFasten the screws Procedure BTop View Procedure a WallRemove the backing from the support blocks Procedure CRemove the backing from the Horizontal To achieve rearward slope for unit draining Remove the backing from the 1113/16 shimOperating Instructions ControlsFAN Fan-only operation Remote controlIncrements of 1 F Air Direction How to insert BatteriesVentilation How to Attach Front Grille to Cabinet Maintenance and ServiceAir Filter Cleaning Normal Operation Common Problems and SolutionsTroubleshooting Memo Nombre del distribuidor Fecha de compra Escriba aquí el modelo y número de serieModelo n Serie n No desmonte ni modifique Tenga cuidado al Los productos Precauciones de SeguridadToma a tierra AparatoNo ponga el cable de alimentación cerca de un calentador Mantenga nivelado el producto al instalarlo No dañe ni use un enchufe de alimentación no especificadoSostenga el enchufe por su cabeza al sacarlo No se suba a la unidad Inserte siempre el filtro Puntiagudos al instalar Ocasiones Del aire durante elLimpieza y mantenimiento Preparación para el funcionamientoUso ServicioCaracterísticas IntroducciónSímbolos Utilizados en Este Manual Seguraida Electrica Datos ElectricosSeguraida Electrica Importante Favorlea CON AtenciónPeríodo de tiempo InstalacionRequisitos DE Instalación Frontal y posteriorInstalación Cómo InstalarProcedimiento a ParedColoque la rejilla plástica Procedimiento BPerspectiva superior Apriete los tornillosAjuste la posición según describe el paso Procedimiento aProcedimiento C Igual a 18, salte al paso 7. Si no, corte lasDel soporte de pared Drenaje de la unidad, retire el envoltorio de lasEl ajuste se muestra en pantalla Instruccionnes de FuncionamientoControles Del ventilador, control de temperatura en 72 FIncrementos de 1 F Control remotoReinicio automático El ajuste aparece en pantallaDirección del aire Cómo Poner Las BateriasVentilación Como agregar la rejilla frontal al gabinete Cuidado y MantenimientoLimpieza del filtro de aire Operación anormal Problemas y soluciones habitualesOperación normal Gire el control de Temperatura a un número más bajoNota Nota Aire Acondicionador Garantía Limitada DEL Aire Acondicionador LG EE.UU LG Room AIR Conditioner Limited Warranty USA Patent No. Us 6, 412 No. MFL38279101

LT1430CR specifications

The LG Electronics LT1430CR is an impressive window air conditioning unit designed to deliver optimal cooling in various small to medium indoor spaces. With its compact design and energy-efficient performance, the LT1430CR has become a popular choice among consumers looking for relief from the summer heat.

One of the standout features of the LT1430CR is its powerful cooling capability. With a cooling capacity of 14,000 BTU, this unit can effectively cool areas of up to 600 square feet, making it suitable for living rooms, bedrooms, and even small office spaces. LG has integrated innovative cooling technologies, ensuring that the air conditioner maintains your desired temperature with efficiency and precision.

Energy efficiency is a key consideration in today's market, and the LT1430CR excels in this respect. It is equipped with an Energy Efficiency Ratio (EER) that allows users to save on energy bills while still enjoying a comfortable environment. The unit also features multiple fan speeds and cooling settings, allowing for personalized climate control to suit various preferences and needs.

The LT1430CR is designed for easy installation, featuring a window mounting kit as part of the package. Its lightweight build ensures that homeowners can manage installation without professional help, saving both time and money. Furthermore, the air conditioner’s sleek and modern design makes it a stylish addition to any room decor.

Ease of use is enhanced with the inclusion of a remote control, enabling users to adjust settings from a distance. Additionally, the programmable timer allows users to set the unit to operate at specific times, promoting energy savings even when the unit is not in use. The air conditioner also incorporates an auto-restart function that ensures the unit resumes previous settings after a power outage.

Another significant characteristic of the LT1430CR is its quiet operation, which is particularly appreciated in residential settings. The low noise levels enable users to enjoy a peaceful environment while the unit efficiently cools the space.

In summary, the LG Electronics LT1430CR embodies advanced cooling technology, remarkable energy efficiency, and user-friendly features. With its powerful performance, easy installation process, and stylish aesthetics, it stands out as a reliable option for those looking to beat the heat and enhance their indoor comfort. The LT1430CR remains a noteworthy contender in the competitive air conditioning market, and its features reflect LG’s commitment to quality and consumer satisfaction.
Top Page Image Contents