Lasko 5521 Control Automático DE Temperatura, Oscilación, Función DE Temporizador, Control Remoto

Page 2

MODELO 5521

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce the

risk of fire, electrical shock and injury to persons, including the following:

Read all instructions before using this Heater.

1.DO NOT PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MUL- TIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.

2.AVOID THE USE OF EXTENSION CORDS BECAUSE THE EXTENSION CORD MAY OVERHEAT AND CAUSE A RISK OF FIRE. HOWEVER, IF YOU HAVE TO USE AN EXTENSION CORD, MINIMIZE THE RISK OF OVERHEATING BY USING THE SHORTEST CORD POSSIBLE AND BY ENSURING THAT IT IS UL LISTED. THE CORD SHALL BE A 3-WIRE, GROUNDING TYPE, WITH NO. 14 AWG MINIMUM SIZE AND RATED NOT LESS THAN 1875 WATTS (15A). NEVER USE A SINGLE EXTENSION CORD TO OPERATE MORE THAN ONE HEATER. NEVER USE A CORD REEL.

WARNING: Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug fits tightly into outlet be- fore each use. During use, check to make certain the Heater plug is not overheating. If necessary have a qualified electrician check and/or replace the wall outlet.

3.Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.

4.Make certain that the room is equipped with a working smoke detector.

5.Make certain that the power source conforms to the electrical requirements of the Heater.

6.Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left operating unattended.

7.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

8.Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.

9.To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.

10.Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.

11.Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.

FUNCIONAMIENTO (Figuras 1 a 3)

1.Cuidadosamente retire el Calefactor de la bolsa y de la caja.

2.Coloque el Calefactor sobre una superficie firme y plana. ADVERTENCIA: Los tacos de plástico o hule, tales como las patas de esta unidad, pueden pegarse a la superficie de los muebles y/o a los pisos de madera. La unidad podría dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes en el acabado de ciertas superficies de muebles, incluyendo superficies de madera y/o pisos de madera.

3.Conecte el cable eléctrico a un tomacorriente eléctrico de 120V~. Asegúrese que el enchufe encaje firmemente en el tomacorriente.

4.Cuando el Calefactor se conecte por primera vez, se oirá un “bip” permanecerá encendida hasta que el Calefactor sea desconectado del tomacorriente eléctrico.

5.ENCIENDA el Calefactor oprimiendo el Botón de Encendido ().

6.Cuando se lo encienda por primera vez, el Calefactor mostrará la temperatura actual de la habitación en grados

Fahrenheit. Oprima los botones () y ( ) al mismo tiempo para cambiar la pantalla a grados Celsius. Oprima los dos botones al mismo tiempo nuevamente para cambiar la pantalla y volver a grados Fahrenheit.

7.Al encender el Calefactor, la unidad estará en calor ALTO () (1500 vatios) y mostrará la temperatura actual de la habitación

(Figura 2)

8.Oprima el botón () para calor BAJO (). (900 vatios)

9.Para APAGAR el Calefactor, presione el Botón de Encendido () y desconecte el Calefactor del tomacorriente eléctrico.

Pantalla al ser encendido por primera vez

Función de Temporizador

Función de Temporizador

en Calor Alto y control

en Calor Bajo

automático de temperatura

Figura 2

 

CONTROL AUTOMÁTICO DE TEMPERATURA:

Oprimir el botón () o el botón ( ) le permite a usted fijar la temperatura deseada del Calefactor. (Figura 3)

1.Cuando el botón () o el botón ( ) esté presionado, la pantalla exhibirá la temperatura fijada y el símbolo () aparecerá.

2.Oprima el botón () para aumentar la temperatura fijada deseada o presione el botón ( ) para reducir la temperatura fijada deseada.

3.Cuando la temperatura del aire alcance los 2 grados por encima de la temperatura fijada, el Calefactor se apagará.

4.Cuando la temperatura del aire alcance un 1grados por debajo de la temperatura fijada, el Calefactor se encenderá.

5.Esta función se cancelará si el botón () es oprimido y el Calefactor ahora estará en calor Alto ().

NOTA: Es normal que el Calefactor alterne entre ENCENDIDO y APAGADO para mantener la temperatura FIJADA.

La pantalla refleja calor Alto y la función de Control

Automático de Temperatura

DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG HEATER BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE HEATER IS ON OR PLUGGED IN.

12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings

may become blocked.

Figura 1

Figura 3

13.

Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power

 

Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw

 

rugs, runners, or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.

14.

This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater.

 

Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the

 

Heater and keep them at least 1 foot (0.3 m) from the sides and rear.

15.

A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are

 

used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This Heater

 

is intended for general use ONLY.

16.

This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar

 

indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.

17.

DO NOT use Heater outdoors.

18.

Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs, move

 

the Heater to another location.

19.

Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.

20. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer

 

to National Electric Code (NEC) Article 547-7 (2002), or applicable state or local codes or standards relating to electrical requirements for

 

Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2002).

21.

This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or

 

local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE

 

REQUIREMENTS OF NEC ARTICLE 500 (2002).

WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.

SAVE THESE INSTRUCTIONS

OSCILACIÓN:

Oprimir el Botón de Oscilación () le permitirá al Calefactor oscilar hacia atrás y hacia delante. Para detener la oscilación, vuelva a oprimir el Botón de Oscilación (). Cuando el calefactor esté en control automático de temperatura, la función de oscilación se detendrá cuando se alcance la temperatura fijada y reiniciará cuando el calefactor vuelva a encenderse.

FUNCIÓN DE TEMPORIZADOR:

La función de temporizador puede ser activada cuando la pantalla del Calefactor está en cualquier función o velocidad. (Figura 2) Esta función le permite fijar la cantidad de tiempo que el Calefactor estará funcionando antes de apagarse automáticamente, de 1 hora a 8 horas. Presionar el Botón de Temporizador () aumentará la cantidad de tiempo en 1 hora cada vez que dicho botón sea oprimido. Después que la pantalla refleje 8 horas, si presiona el Botón deTemporizador () una vez más, se reiniciará el Calefactor para función continua. El Calefactor se apagará cuando el tiempo fijado haya transcurrido. La unidad puede ser encendida nuevamente presionando el Botón de Encendido ().

CONTROL REMOTO:

Todas las funciones realizadas con el Control Remoto operan del mismo modo que los controles manuales, excepto que usted no puede cambiar de grados F a grados C. (Figura 4)

1.Instale las dos baterías “AAA” provistas.

2.No mezcla baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (níquel-cadmio).

3.NO SE DESHÁGA DE BATERÍAS EN EL FUEGO. BATERÍAS PUEDEN ESTALLAR O PUEDEN SALIRSE.

Vista

Vista

Frontal

Posterior

 

+

Figura 4

Si usted pierde su mando a distancia, por favor Cliente de llamada Serive para ordenar un reaplacement en 1-800 -233-0268, de lunes a viernes, entre las 8 a.m. y las 5 p.m. (Horario Estándar del Este de los Estados Unidos).

New 2/07

2

5521ES

New 2/07

7

5521ES

Image 2
Contents Mantenimiento Consejos DE Solución DE ProblemasElementos DE Seguridad Garantía Limitada DE Lasko PRODUCTS, INCFunción DE Temporizador Control Automático DE TemperaturaOscilación Control RemotoRemote Control Timer FunctionAutomatic Temperature Control OscillationLasko PRODUCTS, INC. Limited Warranty Safety Feature Trouble Shooting TipsMaintenance Customer Service

5521 specifications

The Lasko 5521 is an impressive tower fan that combines performance, style, and the latest technology to provide optimal cooling comfort for any space. Renowned for its sleek design, this fan is perfect for home or office use, seamlessly blending into modern decor while delivering powerful airflow.

One of the standout features of the Lasko 5521 is its three-speed settings, allowing users to customize the airflow to their liking. Whether you prefer a gentle breeze for a quiet evening or a stronger fan for hot summer days, the adjustable speeds cater to all needs. This versatility ensures that you can create the ideal environment, no matter the temperature outside.

Another notable characteristic of the Lasko 5521 is its oscillation feature. The fan can pivot side to side, distributing air evenly throughout the room. This oscillation allows for comprehensive air circulation, making it a great option for larger spaces, as it cools more effectively than stationary fans. With a simple press of a button, users can achieve optimal airflow regardless of where they are in the room.

Lasko has integrated innovative technology into the 5521 by equipping it with a built-in timer function. This feature enables users to set the fan to operate for a predetermined duration, promoting energy savings and convenience. Whether you're leaving for work or going to bed, the timer ensures that the fan will shut off automatically after a designated time.

The Lasko 5521 is also designed for user-friendly operation. The fan comes with a remote control, allowing users to adjust settings from a distance. This convenience means you can change the speed or oscillation without having to get up, making it easy to stay comfortable even from the comfort of your couch or bed.

For safety, the Lasko 5521 includes a patented safety fuse technology. This feature provides an extra layer of protection by shutting down the fan in the event of overheating, giving users peace of mind while using the fan, especially during those sweltering summer nights.

In summary, the Lasko 5521 is the ideal solution for anyone looking for a high-performing, stylish, and user-friendly fan. With its adjustable speeds, oscillation feature, built-in timer, remote control, and safety technology, it stands out as a reliable and efficient cooling option for any environment. Whether you need a gentle breeze or powerful air circulation, the Lasko 5521 delivers comfort and convenience in one exceptional package.