GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
1.Make certain the power source conforms to the electrical requirements of the Fan.
2.Make certain that the room is equipped with a working smoke detector.
3.Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.
4.To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.
5.Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6.This Fan must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres where gasoline, paint or flammable liquids are used or stored.
7.DO NOT use Fan in or near a window. Rain may create an electrical hazard.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. Match wide blade of plug to wide slot. Fully insert. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.
This plug is a safety feature, to reduce the risk of fire, electric shock and personal injury. DO NOT remove, replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it may be due to the safety device incorporated in this plug. Return to an authorized service center or call 800-233-0268, Monday - Friday, between 8:00 a.m. and 5:00 p.m. Eastern. If the plug warning label is missing or damaged, call the toll free number for a replacement label.
8.Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an exten- sion cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed. NEVER use a single extension cord to operate more than one Fan. DO NOT plug Fan into any other cord connected device, such as a power strip, cord reel, surge protector, mutiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.
9.NEVER operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner. There are no user serviceable parts. Return Fan to an authorized service facility for examination, electrical or mechanical adjustment or repair.
10.NEVER insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire, or damage the Fan. To reduce the risk of fire, DO NOT block or tamper with the Fan in any manner while it is in operation.
11.Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power Cord so the Fan or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.
12.This Fan is not intended for use in wet or damp locations. Never locate a Fan where it may fall into a bathtub or other water container. NEVER use Fan where flammable liquids are used or stored.
13.NEVER use Fan outdoors.
14.This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical require- ments for Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
15.This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET THE REQUIRE-
MENTS OF NEC ARTICLE 500 (2008).
FUNCIONAMIENTO (Figuras 1 y 2)
1.Cuidadosamente retire el Ventilador de la bolsa plástica y la caja.
2.Coloque el ventilador sobre una superficie firme y nivelada.
ADVERTENCIA: Los tacos de plástico o hule, tales como las patas de esta unidad, pueden pegarse a la superficie de los muebles. La unidad podría dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes en el acabado de ciertas superficies de muebles, incluyendo superficies y pisos de madera.
3.Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos en los tomacorrientes, pueden deslizarse parcial o completamente fuera del tomacorriente con un leve movimiento del cable adosado. Los tomacorrientes en este estado podrían sobrecalentarse y representar un grave peligro de incendio; si está cubierto por una cortina o tela, el riesgo de incendio es aún mayor.
4.Encienda el Ventilador oprimiendo el Botón De Encendido (
). Botón De Encendido se iluminará cuando el equipo haya sido encendido.
5.Al encender el Ventilador, el equipo estará funcionando en ALTO.
6.Si oprime el Botón De Encendido por segunda vez, el Ventilador quedará en MEDIANO.
7.Si oprime el Botón De Encendido por tercera vez, el Ventilador quedará en BAJO.
8.Para APAGAR el Ventilador, oprima el Botón de Encendido/ Apagado (
). La luz de encendido se apagará una vez que el equipo esté apagado.
9.Después de apagar el Ventilador, desconecte la unidad del tomacorriente eléctrico.
Función de oscilación: Esta función podrá ser activada con cualquier velocidad del Ventilador. Si oprime el Botón De Oscilación (
), permitirá que el Ventilador oscile en ambas direcciones. Para detener la oscilación, oprima el Botón De Oscilación una vez más. Botón De Oscilación se iluminará cuando esta función se encuentre activada.
INSTRUCCIONES MULTIDIRECCIONALES
(Figura 2)
La mitad superior del Ventilador puede orientarse en una dirección diferente a la de la mitad inferior del mismo. La función de oscilación podrá activarse con el ventilador enfrentando cualquier dirección.
1.Sostenga la Base y la Parte Inferior De Ventilador en forma estacionaria.
2.Tome la Parte Superior De Ventilador y gírela a la posición que desee.
ADVERTENCIA: NO INTENTE HACER GIRAR EL VENTILADOR MÁS ALLÁ DE SU PUNTO DE RESISTENCIA, PUES ELLO DAÑARÁ EL VENTILADOR.
Parte Superior
De Ventilador
Parte Inferior
De Ventilador
Base
Figura 2
