Shark UV219CS owner manual Cleaning the Hepa Dust Cup Filter, Cleaning the Hepa Filter Frame

Fig. 14

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Cleaning the HEPA Dust Cup Filter

IMPORTANT, Please Note: The Rinseable “TapClean” HEPA Dust Cup Filter will stop most of the tiniest dust particles and airborne allergens from re-entering the air you breathe. In fact it stops 99.97% of all particles as small as 0.3 microns - many times smaller than a human hair!!! Because of this incredible filtration performance, the HEPA Dust Cup Filter will quickly accumulate many fine dust particles inside the white filter folds that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. Clean the HEPA Filter after each use as described in this section.

1. To remove the HEPA
filter, unlock and remove
the dust cup container
cover by turning the cover
to the right until the
arrow on the cover
aligns with the arrow
on the handle and then
lifting the cover off.
2. Remove the HEPA	Fig. 9
Rinseable "Tap Clean"
filter from the dust cup. (Fig. 9)

3.Remove the filter ring that is around the HEPA filter. Vigorously "TapClean"

the HEPA dust cup filter on a hard surface until no more dust is observed falling out. (Fig. 10)

Please note		Fig. 10
that there is a
filter brush
included with
your vacuum. It is located
underneath the dust	Fig. 11
cup cover. You can
use the brush to clean
the pleats of the HEPA
filter. (Fig. 11)
Alternatively, the
HEPA filter may also
be washed by running
it under the tap allowing
the water to run on the
dirty side. (Fig. 12) We
recommend washing it		Fig. 12
once a month or when suction

Please Note: The white material in the HEPA filter will discolor over time - This is NORMAL and will NOT affect the performance of the filter.

Warning: Always empty the dust cup and clean the HEPA dust cup filter before each use and during prolonged usage. Never over fill the dust cup - remove dirt and clean the HEPA dust cup filter each time the dust cup is emptied during prolonged usage or risk motor damage.

Cleaning the HEPA Filter Frame

1.Before replacing the HEPA filter in the HEPA Filter frame, you can (should) rinse the frame in lukewarm water by just running it under the tap to remove any dust that is adhering to the frame. (Fig. 13) Do NOT place in dishwasher.

Fig. 13

2.Make sure that the filter frame is completely dry before replacing into the dust cup.

Cleaning the Filter Ring

1.Around the HEPA filter there is a filter ring. This is washable in lukewarm water.

(Fig. 14) To remove the filter ring, slide it off the HEPA filter.

2.We recommend washing the filter ring when you are washing your HEPA filter. Always allow the

filter ring to air dry for

24 hours before replacing onto

the HEPA filter. Never run the vacuum without all the filters in place.

Note: This is a washable filter, but we recommend replacing it every three (3) months.

Cleaning the Secondary Filter

1.Underneath the HEPA filter there is a secondary filter.

This is washable in lukewarm water. (Fig. 15) We recommend washing it when you are washing your HEPA filter. Always allow the secondary filter to air dry for 24 hours before replacing into the

vacuum. Never run

the vacuum without Fig. 15 the secondary filter in place.

Changing & Cleaning the Pre- Motor Filter

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA filter,changing the filters or performing maintenance/trouble shooting checks.

The pre-motor filter is located in the vacuum underneath the dust cup. Please note that this filter is a washable filter and can be cleaned by rinsing under lukewarm water. Always allow the pre-motor filter to air dry for 24 hours before replacing in the vacuum. Do not use a hair dryer to dry it. Air dry only. To remove the pre- motor filter:

1.Remove the front cover from the vacuum cleaner. (Fig. 16)

2.Remove the dust cup (see instructions on page 5 for removing the dust cup).

3.Clean the pre-motor filter by rinsing under lukewarm water.

4.After air drying for 24 hours, replace in the vacuum.

Changing & Cleaning the Exhaust Filter

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA filter,changing the filters or performing maintenance/trouble shooting checks.

The exhaust filter is located on the front of the unit below where the dust cup is. To remove the exhaust filter, you must first remove the front cover.

1.Check the exhaust filter frequently and clean when dirty.

2.Remove the front cover. (See instructions on page 5.)

3.Remove the exhaust filter out. (Fig. 17)

4.Rinse in lukewarm water and let the filter air dry for 24 hours before re-installing into the vacuum. Do not use a washing machine to rinse the filter. Do not use a hair dryer to dry it. Air dry only. Never operate the vacuum without ALL the filters in place.

5.When the filter is dry, replace into the vacuum and replace the front cover.

Note: A severely soiled or clogged filter should be thoroughly washed with fresh tepid water. A mild detergent can be used if required.

Fig. 17

appears reduced. Always allow 24 hours for drying before replacing into the vacuum.

6

Fig. 16

7