Shark EP733W Accessories, Cleaning the Air Driven Turbo Brush, Power Cord, Using your Vacuum

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Accessories

1.Crevice Tool

For radiators, crevices, corners, baseboards and between cushions.

2.Upholstery Tool

The upholstery tool is used for furniture.

3.Upholstery Brush This snaps onto the upholstery tool.

Air Driven Turbo Brush

The efficiency of your air driven turbo brush depends on the bristle brush rotating at high speed. Strong air suction is needed to accomplish this. In order to ensure that maximum air suction is maintained, please read the following instructions:

1.Change the dust bag frequently.

2.Replace the pre-motor and post motor filters as needed..

3.Ensure that the rotating brush is kept free of hair and string which may accumulate and decrease brush performance.

4.Keep Air Driven Turbo Brush turbine free of dirt and foreign matter. (See Fig. 7 below for cleaning instructions.)

Cleaning the Air Driven Turbo Brush

Locking Latch

Tilt

Upwards

Fig. 7

Turbine

1. Slide locking latch forward then tilt the

top housing of the brush upwards. The

top housing is hinged and will tilt up

approximately 45° only. (Fig. 7)

2. Inspect turbine wheel and air passage

for debris and/or blockage. Remove

debris if present.

3. Inspect the rotating brush for built-up

Power Cord

Your vacuum cleaner includes a power cord which is automatically retractable. To extend the power cord, pull from the rear and extend to desired length. When cleaning is finished, first turn the unit off and disconnect from the electrical outlet. Then press on the cord rewind button to retract the power cord. If the cord does not fully retract, pull it out again and then press on the cord rewind button again. (Fig. 8)

Fig. 8

Warning: Hold the plug when rewinding the cord. Do NOT allow cord to whip when rewinding. Caution: Do not pull the power cord beyond the red mark on the cord as doing this will damage the cord.

Inserting a New Dust Bag

Warning: To reduce the risk of electric shock, the hose, power

nozzle power cord and the power cord must be disconnected before changing the bag or performing maintenance/ troubleshooting.

1.To open the dust bag compartment, remove the flexible hose and the power nozzle power cord. Place your fingers in the opening indentation, lift the front cover up. (Fig. 9)

2.Remove the dust bag support from the dust bag compartment. (Fig. 10)

Dust Bag

Lift Support

3.Holding the dust bag retaining clip, insert the rear part of the cardboard section of the dust bag into the plastic support. Once that rear part is in, release the retaining clip to lock the dust bag in place. (Fig. 11)

Dust Bag

Fig. 11Cardboard

Section

Dust Bag

Retaining Clip

Dust Bag

Support

Caution: Make sure that the dust bag cardboard section is firmly in place in the dust bag support.

4.Insert the dust bag support back into the dust bag support guides in the dust bag compartment making sure that no part of the bag is in contact with the rubber seal and that it is hanging correctly inside the dust bag compartment. (Fig. 12)

Dust Bag

Dust Bag

Support

Dust Bag

Support Guide

Fig. 12

Caution: Make sure that the dust bag support is fully inserted into the dust bag compartment.

5.Close the dust bag compartment cover.

Caution: The dust bag compartment will not close if the

dust bag is not inserted into the unit.

Using your Vacuum

Note: Once all attachments are in place, unwind a sufficient length of the power cord and insert the plug into the wall outlet. A yellow mark on the power cord shows the ideal cable length. Don't pull the power cord beyond the red mark.

1.Insert the power plug into the wall outlet.

2.Press the Power On/Off button located on the unit to turn the vacuum cleaner "On". (Fig. 13)

3.To rewind the power cord, press the cord rewind button with one hand and hold the plug of the power cord with the other hand to ensure that it does not whip causing damage or injury.

(Fig. 14)

Fig. 13 Fig. 14

Dust Bag Full Indicator

The dust bag full indicator may turn on (red) while you are

cleaning to indicate Empty Full that the paper dust

bag is full and Requires replacement. (Fig. 15)

Always change
the dust bag
when the dust bag
full indicator light
comes on.	Fig. 15

Follow instructions on page 5 and 6 “Inserting a New Dust Bag” when changing the paper dust bag.

hair or string. If present, remove by

carefully cutting with scissors. Avoid

damaging or cutting bristles.

4. Once clean, close the top cover of the

turbo brush and slide the locking latch

toward the rear of the brush to lock.

Fig. 9

5

Fig. 10

Never use the vacuum without a dust bag inserted into the unit. NEVER reuse the paper dust bags.

6