Shark EP825 Operating Instructions Problem Solving, Assembling Your Vacuum Cleaner, How to Start

OPERATING INSTRUCTIONS

PROBLEM SOLVING

Assembling Your Vacuum Cleaner

WARNING: Always remove the

power plug from the wall outlet before assembling or removing accessories.

1.Carefully unpack all components, set aside packaging.

2.Lift vacuum body to upright position.

3.Remove the screws (2) that are already attached to the body. (Fig. 1)

4.From the rear of the vacuum, align the handle with groove and slide onto vacuum. If necessary, use thumb and finger pressure to slide handle into position.

5.Once handle is in place, attach the handle with the screws (2).

Fig. 1

How to Start

The upright vacuum can be used on multiple types of carpeting, bare floors or upholstery with attachments. When using the attachment tools such as the crevice tool and the dusting brush, place the handle of the vacuum in the upright position and the carpet height adjustment to the “High Carpet” setting.

1.Adjust the motorized power head for the correct carpet height from low to high.

2.Plug power cord into electrical outlet.

3.Step on the handle release button to release the handle. (Fig. 2)

4.Press the On/Off button to the On position.

5.You are now ready to vacuum.

3

Fig. 2

Carpet Height Adjustment

WARNING: To avoid injury, keep loose clothing, hair, fingers and all other parts of

body away from any moving part (such as the beater brush). Turn off the switch and unplug the vacuum before adjusting the vacuum for the carpet height.

To select a pile height setting:

1.Turn vacuum cleaner "Off".

2.Select a pile height setting by tilting the vacuum cleaner back until the front wheels are lifted slightly off the floor.

3.Turn the height adjustment knob to the desired setting.

Suggested Pile Height Setting:

You may need to raise the height of the vacuum to make some jobs easier, such as scatter rugs and longer pile carpets. Suggested settings are:

:shag carpet, long pile, plush scatter rugs, tools

: medium to long pile

:short to medium pile

:very low pile, hardwood floors

Place unit in "HIGH" setting when using attachments to prevent possible floor damage.

Attention: Special care is required when vacuuming certain types of carpet or floor covering. Always check the carpet or floor covering manufacturer's recommended cleaning instructions before vacuuming.

This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem occurs, it usually can be solved quite easily when the cause is found. Therefore, this checklist is provided for your convenience.

PROBLEM		POSSIBLE CAUSE		POSSIBLE
	1.	Not properly plugged into
		wall outlet.	1.	Plug in firmly.
Cleaner Won’t	2.	No electricity in wall outlet.	2.	Check fuse or breaker.
	3.	On/Off switch not turned	3.	Push on/off switch to on
Run		on.	4.	Reset motor thermostat. (page 7 )
	4.	Motor thermostat tripped.	5.	Reset circuit breaker or replace
	5.	Blown fuse/tripped		fuse.
		breaker.
	1.	Full dust bag.	1.	Change dust bag. (page 5)
			2.	Adjust setting. (page 3)
	2.	Wrong pile height setting.
			3.	Remove obstruction.
	3.	Clogged nozzle.
Cleaner Won't			4.	Remove power head cover and
	4. Clogged dust inlet port.
				remove obstruction.
Pick Up	5. Clogged hose.
			5.	Remove obstruction.
	6.	Broken belt.
			6.	Replace belt. (page 6)
	7.	Hose not inserted fully.
			7.	Push hose in securely.
	8.	Dirty filters.
			8.	Clean / change filters. (page 6)
Cleaner Picks
Up Moveable	1.	Wrong pile height setting.	1.	Adjust setting. (page 3)
Rugs Or Pushes
Too Hard
Agitator Does	1.	Broken belt.	1.	Replace belt. (page 6)
			2.	Check belt changing and agitator
Not Turn	2. Belt installed incorrectly.
				cleaning. (page 6)
Air Flow	1.	Attachment use restricts
Restricted With		air flow.	1.	Check attachment.
Attachment Use	2.	New carpet debris	2.	Remove obstruction.
Sound Changes		clogging air path.

8