Troubleshooting Guide, Problem Solving

OPERATING INSTRUCTIONS cont.

PROBLEM SOLVING

12.Cleaning & Changing the Belt cont.

•Place one end of new belt over motor shaft and the other on the round pulley end of the beater bar.

•Before re-inserting the agitator assembly, make sure that the end caps are on correctly. (fig. R)

Fig. R

•After checking the caps, re-install the agitator assembly into the housing grooves.

•Turn the agitator by hand to make sure that the belt is not twisted and all rotating parts turn freely.

•Replace the rear belt cover and screw firmly.

Caution: The two end caps may come off along with the two washers as you lift the agitator unit out. Do NOT lose the two small washers.

13.Changing the Headlight Bulb

Warning: Always disconnect from power source when servicing or cleaning the unit. Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting.

•Turn unit “Off” and unplug from wall outlet.

•Use a Phillips screwdriver and remove the four (4) screws from the top of the motorized power head cover. (See fig. O on page 7)

•With the base cover removed, insert bulb into the socket and twist clockwise. (fig. S)

Note: Always replace the light bulb with the same or smaller wattage size (12V 4W) to prevent damage to the surrounding parts.

14.Motor Thermostat

Important: This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur:

•Push the On/Off button once.

•Disconnect the plug from the power source.

•Check the source of overheating problem. (i.e. clogged hose or filter)

•if clogged hose or filter is found, unclog the hose and replace the filters.

•Wait at least 20 minutes before attempting to reuse the vacuum.

•After unit has cooled down for 20 minutes, plug in the cleaner and push the On/Off button.

The vacuum should start again.

•If the vacuum still does not start, contact EURO-PRO at 1-800-798-7398.

This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem occurs, it usually can be solved quite easily when the cause is found. Therefore, this checklist is provided for your convenience.

TROUBLESHOOTING GUIDE

PROBLEM	POSSIBLE REASON		POSSIBLE SOLUTION

	1.	Not firmly plugged in.	1.	Plug unit in firmly.
CLEANER WON'T	2.	No electricity in wall plug.	2.	Check fuse or breaker.
RUN	3.	Blown fuse/tripped	3.	Replace fuse/reset
		breaker.		breaker.

	1.	Broken or worn belt.	1.	Replace belt.
	1.	Broken or worn belt.	2.	Push hose in firmly.
	2.	Hose end not securely in	2.	Push hose in firmly.
CLEANER WON'T	2.	Hose end not securely in	3.	Empty dust cup.
CLEANER WON'T		place.	3.	Empty dust cup.
PICK UP		place.	4.	Hose is clogged.
PICK UP	3.	Dust cup is full.	4.	Hose is clogged.
	3.	Dust cup is full.		Remove hose and
	4.	Weak suction force.		Remove hose and
	4.	Weak suction force.		remove obstruction.
				remove obstruction.

CLEANING			1.	Empty dust cup
CLEANING	1.	Dust cup is full.		container.
ACCESSORIES	1.	Dust cup is full.	2.	Remove hose and
ACCESSORIES	2.	Hose is clogged.	2.	Remove hose and
WON'T PICK UP	2.	Hose is clogged.		remove obstruction.
WON'T PICK UP				remove obstruction.

Fig. S

EP708 specifications

The Shark EP708 is a highly advanced and innovative vacuum that exemplifies cutting-edge technology in the realm of home cleaning devices. Recognized for its versatility and efficiency, the Shark EP708 is designed to tackle a variety of cleaning tasks, ensuring that your home remains spotless and hygienic.

One of the standout features of the Shark EP708 is its powerful suction technology, which allows it to effortlessly pick up dirt, dust, and pet hair from multiple surfaces. The vacuum is equipped with a robust motor that provides consistent suction power, making it ideal for both hard floors and carpets. Whether you’re dealing with fine dust particles or larger debris, the Shark EP708 delivers exceptional performance.

Another key characteristic of the Shark EP708 is its innovative DuoClean technology. This dual-brush roll system features both a bristle brush and a soft front brush, allowing it to seamlessly transition between different floor types. The bristle brush is perfect for deep cleaning carpets, while the soft brush gently pulls in larger debris and helps capture dust from hard surfaces. This combination ensures a thorough clean without the need to switch attachments.

Additionally, the Shark EP708 comes with a self-cleaning brush roll feature. This technology actively removes hair and debris from the brush roll as you clean, preventing tangles and ensuring optimal performance. This means less maintenance and hassle for users, allowing them to focus on their cleaning tasks.

The vacuum’s versatility is further enhanced by its ability to convert into a lightweight handheld mode. This makes it easy to clean stairs, upholstery, and even vehicles. The Shark EP708 also comes with a variety of useful attachments, including a crevice tool and a dusting brush, enhancing its capability to reach tight spaces and delicate surfaces.

The Shark EP708's user-friendly design includes an easy-to-empty dust cup, LED headlights for improved visibility in dark corners, and a lightweight build that ensures effortless maneuverability. With these features, it stands out as a practical and user-centric appliance.

In summary, the Shark EP708 combines powerful suction, DuoClean technology, self-cleaning capabilities, and versatile design to provide an exceptional cleaning experience. Whether you’re a pet owner, have a busy household, or just want a reliable vacuum, the Shark EP708 proves to be an excellent choice for maintaining a clean home.