Chicago Electric 3914 manual Mounting the Thread Stand

Page 7
REV 03/04

13.Mount the Power Switch under the table top, on the operator’s side. Use the supplied hardware.

Power

Switch

Mounting the Thread Stand

Note: The Thread Stand is designed to be mounted on the Table Stand Kit (Model 03929-not included). Unless indicated otherwise, all parts referred to in this set of instructions are listed in the Bobbin Winder & Thread Stand Unit Parts List found on page 28. During assembly, it will be helpful to refer to that list and the diagram that follows it on page 29.

14. Locate the large hole in the far right corner (from the location that the operator will be seated) of the Table (not included). Place the Rubber Washer (45) and Washer (37) onto the Lower Spool Rest Rod (36) and insert the Rod into the hole mentioned above. Place another Washer (37) over the end of the Rod, and thread on and tighten a Nut (38).

15. Place the Spool Support (46) over the Lower Spool Rest Rod (36) about halfway down. Insert a Screw (31) and Nut (47) through the Support.

Note: The Support has tabs that hold onto the corners of the Nut to make tightening easier. When assembling, place the Nut on the side with these tabs.

Tighten the Screw.

16. Insert the threaded end of the Spool Pin (40) through one of the holes in the top of the arm of the Spool Support (46). Place a Washer (32) and Nut (35) over the end of the Pin and tighten. Place the Spool Rest (41), Spool Mat (42), and the Spool Vibration Stopper (39) over the end of the Spool Pin. Repeat this step for both of the Spool Pins (40).

17. Place the Column Pipe Connector (33) over the top of the Lower Spool Rest Rod (36) until the Rod is about halfway through the Connector. Place a Screw (34) and Nut (35) through the bottom hole in the Connector and finger-tighten.

18. Place the Upper Spool Rest Rod (30) into the top of the Column Pipe Connector (33). Place a Screw (34) and Nut (35) through the top hole in the Connector. Tighten all of the Screws and Nuts in the Connector.

19. Place the Thread Hanger (28) about halfway over the top of the Upper Spool Rest Rod (30). Insert a Screw (31) and Nut (47) through the Hanger as explained in the note in step 14, above. Tighten the Screw and place the Column Cap (29) over the end of the Upper Spool Rest Rod (30).

SKU 03914

For technical questions, please call 1-800-444-3353.

Page

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Sewing Machine Single Needle For technical questions or replacement parts, please callSave This Manual SpecificationsSafety Warnings and Precautions Read all instructions before using this toolSKU Unpacking Sewing Safety PrecautionsAssembly REV 04/03, 05/03 Mounting the Thread Stand Mounting the Bobbin Winder OperationBobbin Winder Operation Winding Thread Onto the Bobbin Setting the Bobbin into the Bobbin CaseAttaching the Needle Threading the Machine Head Adjusting the Stitch LengthAdjusting the Needle Thread Tension Adjusting the Bobbin Thread TensionChanging the Thread Take-up Spring Stroke and Pressure Setting the Hand LifterSetting the Presser Foot Pressure Adjusting the Feed TimingAdjusting Needle-to-hook Timing Adjusting the Height of the Feed DogAdjusting the Height of the Knee Lifter MaintenanceAdjusting the Presser Bar Height Adjusting the Thread Take-up StrokeARM BED Parts List ARM BED Assembly Drawing Main Shaft Thread TAKE-UP Parts List Main Shaft Thread TAKE-UP Assembly Drawing FABRIC--PIERCING Hook Driving Parts List FABRIC--PIERCING Hook Driving Assembly Drawing Presser BAR Parts List Presser BAR Assembly Drawing Feed Mechanism Parts List Feed Mechanism Assembly Drawing Lubrication Parts List Lubrication Assembly Drawing OIL Reservoir & Knee Lifter Assembly Drawing and Parts List Machine Head Accessories Parts List and Assembly Drawing Bobbin Winder & Thread Stand Unit Parts List Bobbin Winder & Thread Stand Unit Assembly Drawing Limited 90 Day Warranty

3914 specifications

The Chicago Electric 3914 is a notable portable generator that caters to both casual users and serious outdoor enthusiasts. Known for its reliability, versatility, and performance, this generator has become a preferred choice for those in need of temporary power solutions, whether on a job site, during a camping trip, or in the event of a power outage.

One of the standout features of the Chicago Electric 3914 is its robust power output. With a peak wattage of approximately 4,000 watts and a running wattage of about 3,500 watts, it is well-suited for powering a variety of tools and appliances. Its performance makes it capable of running heavy-duty equipment like saws, drills, and refrigerators, ensuring that users can complete their tasks efficiently.

In terms of design, the Chicago Electric 3914 boasts a compact and portable structure, making it easy to move and store. It typically includes a sturdy handle and wheels that facilitate transportation, which is particularly advantageous for users who need to transport the generator across job sites or outdoor areas.

Another notable characteristic of this generator is its fuel efficiency. Utilizing a four-stroke engine, it not only provides ample power but also minimizes fuel consumption, allowing for longer runtimes between refueling. This feature is particularly beneficial for users who require continuous power for extended periods.

The Chicago Electric 3914 is equipped with multiple outlets, including standard 120-volt household outlets and 12-volt DC outlets, offering versatility in powering various electronic devices. It also often includes safety features such as overload protection and low oil shutdown, which protect the generator from damage and ensure safe operation.

Ease of use is another essential aspect of the Chicago Electric 3914. Many models come with a simple pull-start mechanism and easy-to-read gauges, making it user-friendly, even for those who may be new to using portable generators. Additionally, maintenance is straightforward, with accessible components that promote hassle-free servicing.

In summary, the Chicago Electric 3914 stands out in the portable generator market due to its powerful performance, fuel efficiency, portability, and safety features. Whether for work or play, it serves as a reliable power source for a wide range of applications, making it a valuable investment for anyone in need of dependable electrical support.
Top Page Image Contents