Reloading, Creosote Formation and Need for Removal

RELOADING

Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air controls to maximum a few seconds prior to opening the stove's door. Then proceed by opening the door very slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draught and thus eliminate the smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to the front of the stove and reload the unit.

For optimal operation of your wood stove, we recommend you operate it with a wood load approximately equivalent to the height of fire bricks.

It is important to note that wood combustion consumes ambient oxygen in the room .In the case of negative pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh air intake system on an outside wall. Refer to page 16 of the present manual.

WARNINGS

∙NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED, OVER FIRING IS HAPPENING. READJUST THE AIR INTAKE CONTROL AT A LOWER SETTING.

∙THE INSTALLATION OF A LOG CRADLE IS NOT RECOMMENDED IN YOUR DROLET WOOD STOVE.

∙NEVER PUT WOOD ABOVE THE FIREBRICK LINING OF THE FIREBOX.

CREOSOTE FORMATION AND NEED FOR REMOVAL

When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire. When burning wood, the chimney connector and chimney should be inspected at least once every two months during the heating season to determine if a creosote build-up has occurred.

We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately 18" above the stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke exhaust system. The ideal temperature for these gases is somewhere between 275o F and 500o F. Below these temperatures, the build-up of creosote is promoted. Above 500 degrees, heat is wasted since a too large quantity is lost into the atmosphere.

TO PREVENT CREOSOTE BUILD UP

∙Always burn dry wood. This allows clean burns and higher chimney temperatures, therefore less creosote deposit.

∙Leave the air control fully open for about 10 min. every time you reload the stove to bring it back to proper operating temperatures. The secondary combustion can only take place if the firebox is hot enough.

∙Always check for creosote deposit once every two months and have your chimney cleaned at least once a year.

HT-1600, HT-2000 specifications

The Drolet HT-1600 and HT-2000 are remarkable wood stoves designed to enhance the heating efficiency and comfort of any home. Both models stand out for their innovative features, cutting-edge technology, and robust construction, making them ideal choices for homeowners seeking effective and environmentally respectful heating solutions.

The HT-1600 has a heat output capacity of 160,000 BTUs, making it suitable for heating spaces of up to 2,000 square feet. Its compact design doesn’t compromise on performance; it delivers efficient heating while maintaining a traditional aesthetic. The HT-2000, with a higher output capacity of 200,000 BTUs, can effectively heat spaces up to 2,500 square feet. This makes it an excellent choice for larger living areas or open floor plans.

One of the standout features of both models is their high efficiency ratings, typically over 75%. This efficiency translates to more heat produced from each cord of wood used, reducing fuel consumption and lowering heating costs. The stoves utilize a secondary combustion system, which enables a cleaner burn. This technology not only enhances heat output but also minimizes harmful emissions, contributing to a healthier environment.

The HT-1600 and HT-2000 have large fireboxes that allow for longer burn times between refueling, meaning less time is spent adding logs and more time relaxing in a warm, cozy home. Both models feature large viewing windows with heat-resistant glass, providing a comfortable view of the flickering flames. The stylish design enhances any room's ambiance while providing the necessary warmth.

Constructed with durable steel, these stoves are built to last. Their efficient airflow design ensures that heat is distributed evenly throughout the space. The adjustable air control also allows users to fine-tune the burn rate, giving them complete control over how quickly the stove heats the room.

Overall, the Drolet HT-1600 and HT-2000 wood stoves are designed to provide efficient, reliable, and attractive heating solutions for any home. With their advanced technologies, robust construction, and beautiful design, they offer a perfect blend of functionality and style, making them a worthwhile investment for homeowners looking to enhance their heating systems.