Enviro C-10792, 50-1220 owner manual Thermostat / Switch Mode, Initial START-UP See above

Page 8

Operating Instructions

OPERATING YOUR PELLET STOVE:

PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit.

DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN.

MANUAL MODE:

To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The Auger Light will flash with each pulse of the auger (the Auger Feed Rate is pre-programmed during start-up). The Heat Level Indicator will show the Heat Level that the stove will run at after start-up.

If this is the first time the unit has been started or the unit has run out of fuel, the auger will need to be primed. Press the Manual Auger Feed button until fuel starts to drop into the Burn Pot Liner (see

“OPERATING INSTRUCTIONS; STOVE CONTROLS”).

To OPERATE: When a fire has been established, the System Light will turn solid (after approximately 10

-15 minutes) and the Auger Light will continue to flash to the corresponding Heat Level setting. The Heat Level button can now be pressed at this time to change the desired Heat Level Output setting.

The convection blower (room air blower) will turn on. The speed of this blower is controlled by the setting of the heat level output indicator. The convection blower can be turned OFF by depressing the convection blower control button. For the best efficiency and to prevent cycling, the convection blower should be left on at all times.

When operating on LOW HEAT LEVEL, the feed rate can be adjusted, using the auger trim, for different quality fuels. These settings can be used if the fire keeps going out on low (poor quality fuel). Or if the

low setting is too hot for the room (see “OPERATING INSTRUCTIONS; CONTROL BOARD FUNCTIONS”).

THERMOSTAT / SWITCH MODE:

INITIAL START-UP: See above

OPERATION - HI / LOW mode: When the thermostat contacts are closed the stove settings are adjustable as per Manual Mode (see above). When the thermostat contacts open, the circuit board will take control of the settings. The stove will drop down to a low burn until the thermostat contacts close

again. This low burn setting can be adjusted for different fuel qualities (see “OPERATING INSTRUCTIONS;

STOVE CONTROLS - CIRCUIT BOARD”). The stove will come back to the previous HEAT LEVEL setting when the thermostat contacts close again.

OPERATION – ON / OFF mode: When the thermostat contacts close, the unit will light automatically. Once up to temperature, the stove operates the same as in manual mode (see above). When the thermostat contacts open, the unit automatically begins its shutdown routine. The stove will re-light when the thermostat contacts close again.

TURNING YOUR PELLET STOVE OFF:

•MANUAL and HI / LOW mode: To turn the unit OFF, simply press the ON / OFF button. This will stop the feed of pellets. The blowers will continue to operate and cool the stove down. When cool enough, the stove will turn off.

•ON / OFF mode: To turn the unit OFF, turn the thermostat down or off.

DO NOT unplug unit while Combustion fan is operating.

This may lead to smoke escaping from the stove.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Mini Table of Contents Store pellets at least 36 1 m away from the pellet stove IntroductionI. Pellet Standards USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Dimensions of Bern Rating label is located on the back of the unitReasons WHY the Unit Overheated Heat Level AdjustmentOperating Instructions Heat OutputThermostat / Switch Mode Initial START-UP See aboveSpecial Notes Slider/Damper Plate in UnitRoutine Cleaning and Maintenance Tools Required to Clean UnitExhaust Passages semi-annually ASH PAN weeklyNot Place Unburned or RAW Pellet Fuel in ASH PAN Post Season CLEAN-UP Door Glass ReplacementExhaust Vent annually Blower Mechanisms seasonFor the do-it-yourself Individual WarrantyTo the Distributor Installation Data Sheet Name of Owner Address

50-1220, C-10792 specifications

Enviro C-10792,50-1220 is an innovative solution designed to meet the increasing demands of environmental sustainability while enhancing operational efficiency across various industries. This advanced product has been engineered with a focus on performance, durability, and eco-friendliness, making it ideal for organizations looking to minimize their environmental footprint without compromising on quality.

One of the primary features of Enviro C-10792,50-1220 is its exceptional compatibility with a wide range of materials. The formulation is designed to work seamlessly with various substrates, ensuring a strong bond that enhances the longevity of applications. This characteristic is particularly beneficial in sectors such as construction and manufacturing, where adherence to strict performance standards is essential.

Technology plays a pivotal role in the development of Enviro C-10792,50-1220. The product utilizes cutting-edge nanotechnology to enhance its properties, resulting in increased resistance to environmental stressors such as UV exposure, moisture, and temperature fluctuations. This innovative approach not only improves the product's longevity but also ensures that it maintains its structural integrity over time, reducing the need for frequent maintenance or replacements.

In terms of environmental impact, Enviro C-10792,50-1220 is formulated to be low in volatile organic compounds (VOCs). This characteristic makes it a safer choice for workers and the surrounding environment, aligning with global standards for environmentally friendly materials. By choosing this product, companies can contribute to cleaner air quality and reduced pollution levels, which is increasingly important in today’s regulatory landscape.

Another notable characteristic of Enviro C-10792,50-1220 is its easy application process. The user-friendly formulation allows for quick and efficient installation, reducing labor costs and minimizing downtime. This ease of use does not compromise the performance, ensuring that projects can be completed on time without sacrificing quality.

In summary, Enviro C-10792,50-1220 stands out as a versatile, durable, and eco-friendly solution suitable for various applications. With its advanced technology and robust characteristics, it enables organizations to achieve their sustainability goals while maintaining high performance standards. As industries continue to evolve towards more sustainable practices, Enviro C-10792,50-1220 is poised to play a crucial role in this transformation.
Top Page Image Contents