Pedestal Assembly W3000FS | Breckwell specs

INSTALLATION

PEDESTAL ASSEMBLY – W3000FS

Note: The W3000FS wood stove is heavy. Be prepared to handle the weight to avoid damage or injury. Wearing gloves during installation is recommended.

1.Carefully lay the stove on its back on carpet or other material that will prevent damage to the finish.

2.Align the mounting tabs on the pedestal with the mounting holes in the bottom of the stove making sure that the opening in the pedestal is facing the back of the stove. Using the two 3/8” x 3/8” bolts firmly tighten the pedestal to the stove.

3.Carefully stand the stove back up. If the stove is not centered on the pedestal, loosen the bolts (do not fully remove), realign the stove, and firmly retighten the bolts.

OPTIONAL BLOWER INSTALLATION

WARNING: Electrical Grounding Instructions. This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut o remove the grounding prong from this plug.

Both blower kits contain a blower assembly and speed control unit.

W3000FS

Never operate the stove without either the blower or the blower cover in place.

1.Using a 3/8” wrench or socket, remove the 5 screws holding the blower cover plate in place. Do not discard the cover plate/ (If the blower is ever removed, the cover plate MUST be reinstalled) place it in the pedestal, or any other safe place.

2.Using the 5 screws from step 1, install the blower as shown in figure 4. Firmly tighten the screws, but so not over tighten as you may strip the holes out.

3.Plug the speed control into the nearest outlet. Route the fan cord so that it is not coming into contact with any part if the stove. Plug the blower cord into the speed control unit.

BLOWER ASSEMBLY

W3000FS

W3000I

1.Carefully unpack the blower assembly. Determine which side of the stove the power supply will be located. The blower comes standard with the power cord installed on the right side of the blower housing. If power outlet is on the left side, the blower cord can be rerouted to the left side by removing the rubber grommet and cord, and reinstalling on the left side in the same location.

2.Install blower assembly to the stove face by first loosening the two ¼” cap screws underneath the ash lip. Locate the blower assembly by lining up the screws on the blower housing to the two cap screws. Slide blower housing from left to right, and then tighten the two cap screws.

3.Route the fan cord so that it is not coming into contact within part if the stove. Plug the blower cord into the power outlet.

OUTSIDE AIR KIT – W3000FS ONLY

1.Making sure that all minimum clearances are met, position the stove on the floor protection. Draw an outline around the pedestal on the floor protector. Remove the stove.

2.In the center of the outline of the pedestal foot print, cut a 4 ½” diameter hole through the floor protector and floor. Make four 1 ½” cuts in one end of the tube and fold out to make flaps. Insert the tube through the hole, cover it with the screen, and secure it to the floor protector.

3.Place the stove back on the floor protector. If the stove is to be fastened to the floor, use lag bolts long enough to penetrate well into the floor. Use the mounting holes provided inside the pedestal.

4.Install the pedestal cover by aligning the screw holes in the pedestal with the holes in the cover, making sure that the cover recesses into the pedestal (see figure 5).

5.Using a silicone dealer, seal all cracks between the pedestal cover and the stove, as well as cracks between the floor protector and pedestal base.

FIGURE 4

FIGURE 5

W3000 specifications

The Breckwell W3000 wood burning stove is an exemplary choice for those seeking an efficient and stylish heating solution for their home. Renowned for its robust construction and innovative features, the W3000 stands out in the world of traditional wood stoves.

One of the W3000's main features is its large firebox capacity. With a generous size, it can accommodate logs up to 18 inches long, allowing for longer burn times and fewer reloads. This feature is especially beneficial for homeowners looking for convenience and extended warmth. The firebox is designed with a cast iron door and large glass window, providing an inviting view of the flames while enhancing durability.

The stove is powered by advanced technologies that maximize efficiency and minimize emissions. The W3000 utilizes a unique air wash system that keeps the glass clean, ensuring that the view of the fire remains unobstructed and enjoyable. This technology also helps maintain optimal combustion conditions, resulting in lower particulate emissions, which is a common concern with traditional wood-burning stoves.

An additional characteristic that sets the Breckwell W3000 apart is its heat output capabilities. With a heating capacity of up to 2,400 square feet, it is ideal for larger living areas or open floor plans. This impressive output is complemented by a variable speed blower that allows users to distribute heat evenly throughout the space, enhancing comfort and energy efficiency.

Durability is another hallmark of the W3000. Constructed from heavy-duty steel, it is built to withstand the rigors of daily use while maintaining aesthetic appeal. The stove is available in different finishes, including classic black and a more modern pewter, allowing homeowners to choose a style that suits their decor.

The Breckwell W3000 also prioritizes ease of use, featuring simple controls for adjusting the air supply and heat output. This ensures that even novice users can efficiently operate the stove and enjoy the benefits of wood heating. Overall, the Breckwell W3000 wood burning stove combines efficiency, aesthetics, and user-friendly features, making it a compelling choice for anyone looking to enhance their home’s heating system. With its blend of tradition and modern technology, the W3000 is designed not only to keep you warm but also to create a cozy ambiance in your living space.