3M 800ab 39600 manual Uncrated, Machine BED Height

Page 18

Installation and Set-Up (Continued)

8.Use appropriate material handling equipment to remove the machine from the pallet and move it into position.

Whenever the machine is lifted with a fork truck, insure that the forks span completely across the machine frame and do not contact any wiring or mechanism under the machine frame. In some cases the lower taping head may need to be removed to avoid damage.

CAUTION – Machine weighs approximately 114 kg [250 pounds]

uncrated.

9.Continue with the remainder of the installation and set-up procedure on this page.

MACHINE BED HEIGHT

Adjust machine bed height. The case sealer is equipped with four adjustable legs that are located at the corners of the machine frame. The legs can be adjusted to obtain different machine bed heights from 610 mm [24 inches] minimum to 890 mm [35 inches] maximum.

Refer to Figure 2-3C and set the machine bed height as follows:

1.Raise and block up the machine frame to allow adequate leg adjustment.

2.Loosen, but do not remove, two M8 x 16 socket head screws in one leg (use M6 hex wrench). Adjust the leg length for the desired machine bed height. Retighten the two screws to secure the leg. Adjust all four legs equally.

TAPE WIDTH

The taping head has been pre-set to accommodate 48 mm [2 inch] wide tape rolls. To adjust heads for narrower tape, refer to Section II , "Adjustments – Tape Web Alignment", page 11.

TAPE LEG LENGTH

Taping heads are pre-set to apply 70 mm [2-3/4 inch] long tape legs. To change tape legs to 48 mm [2 inch], see "Special Set-Up Procedure – Changing Tape Leg Length", page 23.

ELECTRICAL CONNECTION AND CONTROLS

The electrical control box, shown in Figure 3-1, contains the pre-set circuit breaker and can be located on either side of the machine frame for customer operating convenience. A standard three conductor power cord with plug is provided at the back of the electrical control box for 115 Volt, 60 Hz, 1.9 Amp electrical service. The receptacle providing this service shall be properly grounded. Before the power cord is plugged into 115 Volt, 60 Hz outlet, make sure that all packaging materials and tools are removed from the machine. Do not plug electrical cord into outlet until ready to run machine.

Use of an extension cord is not recommended. However, if one is needed for temporary use, it must have a wire size of AWG 16 [1.5 mm dia.], have a maximum length of 30.5 m [100 ft], and must be properly grounded.

WARNING – To prevent shock and fire hazard: Position extension

cord where it will be out of the way of foot or vehicle traffic. Extension cord is only for temporary use – do not use for a permanent installation.

Note –Machines outside the U.S. may be equipped with 220/240 Volt, 50 Hz systems, or other electrical requirements compatible with local practice.

INITIAL START-UP OF CASE SEALER

After completing the "Installation and Set-Up" procedure, continue through "Operation" for tape loading and start-up to be sure case sealer is properly adjusted to run boxes.

13

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 3M-Matic Replacement Parts and Additional Manuals To Our CustomersTo Our Customers Table of Contents Table of Contents Intended Use 800ab Contents Important Safeguards Hands Warning LabelStop and Off/On Labels Safety Instructions label, shown Tape Threading Label This page is Blank Specifications Box Weight and Size Capacities Weight Box SizeMachine Dimensions Minimum MaximumThis page is Blank Installation and Set-Up Receiving And HandlingCable Tie, Taping Head Uncrated Machine BED HeightThis page is Blank Operation Case Sealer Components, Left Front ViewEmergency Stop Switch Tape Loading/ThreadingBox Size Set-Up From the machine before operatingWill occur Box Sealing Maintenance LubricationCould result Circuit Breaker Drive BeltsBox Drive Assembly, Infeed End Adjustments Taping Head AdjustmentsCould result Drive Belt Tension Special Set-Up Procedure Drive Belt Assembly HeightDrive Belt Assembly, Reassembly Troubleshooting Troubleshooting Guide Problem Cause CorrectionElectrical Diagram Electrical DiagramSpare Parts 800ab Adjustable Case Sealer, TypeSpare Parts/Tools Tool KitOptions/Accessories Part Number Option/AccessoryReplacement Parts Illustrations and Parts List This page is Blank Page 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Ref. No 3M Part No Description 800ab Adjustable Case Sealer Safety and Information Labels 800ab Safety and Information Labels Ref. No 3M Part No Description Qty

800ab 39600 specifications

The 3M 800AB 39600 is a versatile, high-performance adhesive that has rapidly gained recognition across various industries for its superior bonding capabilities and innovative formulation. This adhesive is engineered to offer robust performance while catering to a wide range of applications, making it an essential product for manufacturers and professionals alike.

One of the standout features of the 3M 800AB 39600 is its exceptional adhesion to a variety of substrates. It demonstrates excellent bonding properties on materials such as metals, plastics, ceramics, and wood. This flexibility makes it ideal for applications in automotive, aerospace, construction, and electronics sectors, where different materials often come together in one project.

The technology behind 3M 800AB 39600 revolves around its dual-component system. It consists of a resin and hardener that, when mixed, undergo a chemical reaction to form a durable bond. This curing mechanism ensures that the adhesive achieves optimal strength and reliability, enhancing its overall performance under demanding conditions. The adhesive is designed to cure at room temperature, providing convenience and efficiency in both industrial settings and smaller repair applications.

Another notable characteristic of the 3M 800AB 39600 is its resistance to environmental factors. It offers excellent resistance to heat, moisture, and various chemicals, ensuring that the bonded joints maintain their integrity even in challenging conditions. This durability is particularly beneficial in outdoor applications or in environments subject to temperature fluctuations and exposure to harsh substances.

Furthermore, 3M has placed a strong emphasis on user-friendly application with this adhesive. The material can be applied using standard dispensing equipment, including static mix nozzles that allow for a uniform blend of the resin and hardener. This easy application process minimizes waste and enhances the efficiency of the bonding operation.

In summary, the 3M 800AB 39600 is a high-quality adhesive marked by its strong adhesion to diverse materials, its innovative dual-component technology, and its impressive resistance to environmental challenges. Its versatility and reliability make it an invaluable asset for countless industrial and commercial applications, streamlining processes and ensuring long-lasting bonds in various projects. Whether for manufacturing, assembly, or repair, the 3M 800AB 39600 is a top choice among professionals seeking dependable adhesive solutions.
Top Page Image Contents