Euro-Pro V1055H Cleaning the Filter Ring, Cleaning & Changing the Belt, Using the Attachments

Fig. 3

Warning: Allow 24 hours for drying before replacing in unit.

Fig. A

Wash once a month or when suction appears reduced

Fig. 10

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

PLEASE NOTE: The white pleated filter material in the HEPA-Type Filter will discolor over time -This is NORMAL and will NOT affect the performance of the filter. If the HEPA- Type Filter

is properly "TapCleaned” after each use and suction does not return to 100%, then we suggest that the HEPA-Type filter be “TapCleaned” vigorously until no more dust

can be removed, then rinsed under the faucet and allowed to air dry for 24 hours before refitting into the vacuum. (Fig. A) This should be done once a month or when suction appears to be reduced .

Warning: Always empty the dust cup container and

clean the HEPA-Type filter, filter ring and filter frame before each use and during prolonged usage.

Never over fill the dust cup container - remove dirt and clean the HEPA-Type filter, filter ring and filter frame when dirt in dust cup is at or below the “FULL" level or during prolonged usage because you could risk damaging the motor.

If you wash the Hepa-Type filter and filter ring, make sure that they have completely air dried for 24 hours before inserting back into the vacuum.

Please Note: The HEPA-Type Filter is washable. It should, however, be replaced every three (3) to six (6) months to ensure peak performance of your vacuum.

The filter ring is also rinseable but should be air dried for 24 hours before replacing into the vacuum. It should however be replaced every three (3) months to ensure peak performance of your vacuum. Important: Make sure that ALL filters are completely dry before re-installing back in the vacuum.

Cleaning the Filter Ring

1.Around the HEPA-Type filter there is a filter ring. This is washable in lukewarm water. (Fig. 10) To remove the filter ring, slide it off the HEPA-Type filter.

2.We recommend washing the filter ring when you are washing your HEPA-Type filter.

Always allow the filter ring to air dry for

24 hours before replacing onto

the HEPA-Type filter. Never run the vacuum without all the filters in place.

Note: This is a washable filter, but we recommend replacing it every three (3) months.

Cleaning & Changing the Belt

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA-Type filter,changing the filters or performing maintenance/trouble shooting checks.

Occasionally the power head drive belt will require changing, the frequency will depend upon the amount of use your vacuum sees.

1.Turn the vacuum "Off" and unplug from power supply.

2.Release the handle by pressing the handle release pedal and pull back on the handle unit it releases from its upright position, and turn the unit over on the floor.

3.With a #2 Phillips screw driver, remove the four (4) screws on the bottom base plate. There are two in the front of the unit and 2 screws recessed in the back.

4.With the unit still lying down, hold the top and bottom plates together while turning the unit over. Remove the one

(1) screw that holds the carpet height adjustment button Lift the cover of the power head starting from the back.

Assembling Your Vacuum Cleaner WARNING: Always remove the power

plug from the wall outlet before assembling or removing accessories.

Assembling the Vacuum Cleaner

1.Carefully unpack all the components, set the packaging aside.

2.Lift the vacuum body to the upright position.

3.Insert the handle into the handle inlet of the vacuum.

4.Press down on the telescopic tube height adjustment button while pushing the telescopic tube down. (Fig. 1)

Telescopic Tube

Height Adjustment

Button

Fig. 1

5.To remove the telescopic tube, extend it to its maximum height by depressing the telescopic tube height adjustment button and then press the telescopic tube release button and pull the tube out. (Fig. 2)

Telescopic Tube

Release Button

Using the Attachments

1.Place vacuum in its upright position. Make sure that the vacuum cleaner is NOT plugged into the electrical outlet when adding or removing accessories.

2.Turn the carpet height selector to the highest position.

3.Remove the telescopic tube from the unit following the instructions on page 4.

4.Remove the hose connector from the side of the unit.

5.Insert the flexible hose into the top of the handle. (Fig. 3)

6.Insert the desired

attachment firmly onto the end of the telescopic tube.

Warning: When the vacuum is turned on, the beater brush will continue to rotate. AVOID tipping the vacuum or setting it on furniture, fringed area rugs or carpeted stairs while you are using the hose with attachments. AVOID leaving the vacuum in one place for an extended period of time, particularly on thick carpet.

Crevice Tool

For radiators, crevices, corners, baseboards and between cushions.

Dusting Brush

The dusting brush is used for the furniture, Venetian blinds, lamp shades, shelves, etc.

Caution: Do NOT pull the vacuum cleaner around the room by the hose as it could tip over and cause damage. When using the attachments, Do NOT over extend the hose length when reaching. Trying to reach beyond the hose reach could cause the vacuum to tip over. The dust cup cover handle can be used to lift the vacuum when changing locations.

Fig. 2

7

4