Euro-Pro BPV325H Using the Air Driven Turbo Brush, Using the Attachments, Blower Attachments

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

2.Step on the floor to carpet selector to adjust the height of the brushes. There are two (2) different heights one for floors and one for carpets. (Fig. 12)

Floor to

Carpet

Using the Air Driven Turbo Brush

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the HEPA dust bag, the shake-out bag, HEPA pre-motor filter, changing the filters or performing maintenance or

3.Using your thumb and index finger, simultaneously squeeze the locking tabs on either side of the trap door and lift off. (Fig. 14) Doing so will remove the trap door and allow you access to the turbine for cleaning and maintenance purposes. (Fig. 15)

The blower attachments have air bleed holes. These air bleed holes help relieve some air pressure so that the attachment does not blow off. However, should an increase in air pressure be desired, simply cover one or more of the air bleed holes.

selector

Fig. 12

3.To remove the telescopic tube from the floor to carpet brush, pull the telescopic tube out from the floor to carpet brush.

Using the Attachments

troubleshooting checks. The efficiency of your air driven turbo brush depends on the bristle brush rotating at high speed. Strong air suction is needed to accomplish this. In order to ensure that maximum air suction is maintained, please read the following instructions:

1.	Change the HEPA dust bag or empty
	the shake-out bag frequently.
2.	Replace the pre-motor and exhaust
	filters as needed.

Locking

Tabs

Fig. 14

Trap Door

To use the blower attachments:

1.Pull up and hold the exhaust tab, with the free hand pull out the exhaust grill. (Fig. 16)

Exhaust

Tab

Exhaust

Grill

Dusting Brush

The dusting brush is used for the furniture

Crevice Tool

Use for radiators, crevices, corners, baseboards and between cushions.

Pet Hair Remover Brush

3.	Ensure that the rotating brush is kept
	free of hair and string which may
	accumulate and decrease brush
	performance.
4.	To attach the air driven turbo brush,
	insert the telescopic tube into the air
	driven turbo brush.

Turbine

Fig. 15

4. There may be some dust, lint, hair,

etc on the turbine wheel. Remove as

Fig. 16

2.Remove the exhaust filter.

3.To place the blower port into the exhaust outlet, align the lower tabs on the blower port with the slots on the exhaust. Pull up on the exhaust tab and push the top of the blower port until it snaps into place. (Fig. 17)

The pet hair remover brush is used for upholstery. The unique surface makes it an excellent tool for removing unwanted pet hair.

Note: This tool is not a grooming tool and should not be used on animals.

Caution: Do not use pet hair

How To Clean the Air Driven Turbo Brush

From time to time, the turbine of your air driven turbo brush will require cleaning. To do this:

1.	Remove the turbo brush from the
	telescopic tube.
2.	Flip the turbo brush over so that the
	bottom of it is facing upwards.

much of this as possible.

5. You may also use the unit’s hose with

the crevice tool attached and use the

vacuum to remove any additional

debris from the turbine.

6. Ensure that the turbine wheel moves

freely by rotating it with your finger. If

the turbine does not rotate, call EURO-

PRO Customer Service for help at

1 (800) 798-7398.

Blower

Port

Exhaust Tab

Fig. 17

remover brush on delicate or woven fabrics that may snag.

DO NOT use pet hair remover brush on wooden floors as this accessory might cause mild scratching.

Blower Attachments

The blower attachments can be used with the vacuum to pick up very fine dirt particles in tight crevices or spots, or to inflate inflatable items or air mattresses.

(Fig. 13)

Fig. 13

7. Once clean, replace the trap door of

the turbo brush. Ensure that it clicks

into place.

Using the Blower Attachments

The blower attachments are extremely useful for vacuuming in hard to reach crevices and small compartments such as in cars.

Important Note: When blocking the air bleed holes, grasp the blower attachments firmly so that they do not blow off.

Note: Do not use blower function to clear dust off of fragile or delicate objects unless they are secured or held firmly in place as the blower action is quite strong and could cause damage.

4.To attach the hose to the blower port, align the flexible hose and turn counter-clockwise until it stops. The hose is now securely in place.

(Fig. 18)

Fig. 18

6

7