HOW TO ASSEMBLE
F
C
A
B
A
Fig. 1
E
D
Step 1 - Assemble the Handle
Slip the upper handle and the lower handle together so the handle bolt holes align and the slots in the handle are positioned as shown in Fig. 1. Insert a
Step 4 - Outer Bag
Hold outer bag with zipper away from handle. Important: To provide a good gasket seal, the bag coupling must seat firmly against the motor base. Start the bag screws by hand, then tighten with a screwdriver.
Step 5 - Bag Support
Slip the ring at the top of the cloth bag over the bag support hook on the back of the cord hook.
HOW TO USE
The upright vacuum cleaner is designed to be used on multiple types of carpeting. Do not attempt to use the upright vacuum cleaner on bare floors, as damage to the floor covering may result.
center of the handle and tighten.
Hold the assembled handle so it curves away from the cleaner. Then push the handle into the handle socket (E) at the rear of the cleaner. Align the holes, insert the other
Step 2 - Attach Lower Cord Hook |
|
|
|
|
| ||||
Insert the power cord into the lower cord hook |
|
|
|
|
| ||||
|
|
|
|
| |||||
(B), as shown. Snap the hook into the lower |
|
|
|
|
| ||||
handle. Pull up on the cord to tighten but leave |
|
|
|
|
| ||||
enough slack near the base so the cord is not |
|
|
|
|
| ||||
|
|
|
|
| |||||
strained when the handle is lowered. |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| |
Step 3 - Attach Upper Cord Hook |
|
|
|
|
|
|
| ||
Pull the sleeve (F) on the electrical cord |
|
|
|
|
|
|
|
| |
|
|
|
|
| |||||
|
|
|
|
|
| ||||
upward toward the top of the handle. Make |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| ||||
sure slots in handle are positioned properly, |
|
|
|
|
|
|
|
| |
|
| BAG | |||||||
Fig 1. |
|
|
|
|
| ||||
|
| ||||||||
Insert the lower half of the sleeve (F) into |
|
|
|
| SUPPORT | ||||
|
|
|
| ||||||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| |||
the upper cord hook (C) as shown. Snap |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
the hook into the upper handle, directions |
|
|
|
|
|
| |||
below. |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
Handle Adjustment
With the tip of the foot, press down to release the handle lock located at the left rear side of the cleaner. Move the handle and adjust it to the desired position for
(1)storing upright, (2) operating the cleaner at a comfortable height for the user, and (3) cleaning underneath low furniture.
Power Switch
The power switch is mounted on the motor hood near the handle. Switch style varies by model and may differ from the illustration. A push with the foot turns the motor ON; push again to turn the motor OFF.
1. Store
2. Use
3.Clean Underneath
Handle Lock
ON/OFF
1. Place inner | 2. Press hook | 3. SNAP opposite |
tab into | around | inner tab into |
slot | handle | place |
Cord Storage
The cleaner has two convenient cord storage hooks attached to the handle.Wind the cord around the hooks for storage. Fasten the plug to the cord to prevent unwinding.
3