Product Features (Fig. A)
1. | On/Off slide switch | 4. | Wall mountable charging base | 7. Filter cleaning wheel |
2. | Bowl release button | 5. | Charger | |
3. | Dust bowl | 6. | Charge indicator light | |
How To Use
INSTALLATION INSTRUCTIONS (FIG. B)
Fix the charging base within reach of an electrical outlet, using the screws supplied. Plug in and place the product in position. Always mount in an upright (handle up) position.
NOTE: Avoid damaging the cord while fixing the base to the wall or when removing or replacing the product from the base.
RECHARGING (FIG. C)
From new, the rechargeable cells of the product need a minimum charge time of 16 hours to ensure full power. While charging the charge indicator light will be illuminated. The switch must be in the off (“O”) position. The product will not charge if it is in any other position. While charging, the product may get warm, this is perfectly normal and safe. It can remain on charge indefinitely without damage or danger. It is not possible to “overcharge” the battery cells with the charger provided.
THIS PRODUCT IS FOR DRY PICK-UP ONLY.
OPERATION
SWITCH (FIG. D)
To start, slide the On/Off switch forward (i.e. “O”= Off, “I” = On). To stop, slide the switch back.
Always return the product to the charging base immediately after use so that it will be ready and fully charged for the next use. Ensure that the product is fully engaged on the charging base.
CLEANING THE PRODUCT (FIGS . E-I)
WARNING: Never use the Dustbuster without its filters.
NOTE: The filters are re-usable, do not confuse them with disposable dust bags, and do not throw them away when the product is emptied. We recommend that you replace the filters every 6-9 months depending on frequency of use. (Use Cat. No. VF100 filters)
FIG. E • Remove the dust bowl by pressing the dust bowl release button and pulling the bowl down and out. To replace the bowl, place it back onto the handle and click firmly into position.
Important: For best vacuum results, empty bowl after every use. FIG. F • Empty the debris from the bowl and wash if necessary (see Fig. H).
FIG. G • To remove the filters twist the outer (plastic) filter in a clockwise direction. Shake or lightly brush any loose dust off the outer filter. Remove the inner filter and shake, tap or lightly brush outside surface to remove loose dust. Both filters can be rinsed as shown in fig. (H). 
WARNING: Filter must be dry before re-assembling.
Ensure both filters are in place before operating.
FIG. G1• If your unit is equipped with a filter cleaning wheel as shown in Fig. G1 you can achieve more use between filter cleanings by first switching off the vac, and then rotating
the cleaning wheel up or down as shown. Make two full rotations of wheel for best results. FIG. H • Wash the filters using warm, soapy water and ensure that they are completely dry before
using it again. The cleaner the filters are, the better the product will perform. It is
very important that the filter is correctly in position before use. The dust bowl can also be washed in warm soapy water. Ensure that it is dry before re-attaching.
WARNING: Filters must be dry before re-assembling.
IMPORTANT: Maximum dust collection will only be obtained with clean filters and an empty dust bowl. If dust begins to fall back out of the product after it is switched off, this indicates that the bowl is full and requires emptying.
FIG. I | • The exhaust filter is removed by opening cover and pulling out filter as shown. For best |
FIG. J | results wash filter regularly with soap and water. |
• Never immerse the product in water. A damp cloth and soapy water should be used to clean |
| the exterior of the motor section. Always ensure the product is completely dry before re-use |
| or storing. |
ECONOMIC USAGE
•Your product is very economical to charge. While it is charging it uses less electricity than a typical night light bulb.
•When fully charged and with a clean filter, the average effective usage times vary by voltage.
7.2 volts: 7 - 9 minutes | 9.6-12 volts: 9-11 minutes | 14.0 volts and higher: 12-15 minutes |
TROUBLE SHOOTING
If the product does not work, check the following:
•That the charge indicator light is on when unit is in base.
•The charger was correctly plugged in for recharge. ( It feels slightly warm to the touch.)
•The charger cord is not damaged and is correctly attached to the base.
•The charger is plugged into a working electrical outlet.
•That the switch is in the “OFF” position when charging.
ACCESSORIES
Accessories are stored on the product (FIG. K) and are fitted into the nose of the product for use. Accessory use is shown in FIG. L.
Note: Replacement filters can be purchased from most local/national retailers that sell vacuums. Look for VF100 filters.
BATTERY REMOVAL AND DISPOSAL
This product uses nickel-cadmium (Ni-Cd) rechargeable and recyclable batteries. When the batteries no longer hold a charge, they should be removed from the Vac and recycled. They must not be incinerated or composted.
The batteries can be taken for disposal to a Black & Decker, Company-Owned or Authorized Service Center. Some local retailers are also participating in a national recycling program
(see “RBRCTM Seal”). Call your local retailer for details. If you bring the batteries to a Black & Decker Company-Owned or Authorized Service Center, the Center will arrange to recycle old batteries. Or, contact your local municipality for proper disposal instructions in your city/town.
To remove the battery pack for disposal:
1.Remove accessories from the bottom of the unit.
2.Using a Phillips screwdriver remove the screws as shown in Fig "M". Then use the screwdriver to push the lock tabs in the direction shown.
3.Pull the battery cover off as shown in Fig. N.
4.Using a Phillips screwdriver remove the two battery location screws as shown in Fig "O". After removing the screws push the battery pack back as shown.
5.Remove the battery pack (Fig. P) and dispose as stated above.
To replace or obtain a new battery pack, contact your local Black & Decker, Company-Owned or Authorized Service Center, or call 1-800-54-HOW-TO (544-6986). Be prepared to provide the Catalog No. of your DustBuster, found on the bottom housing under the crevice tool.
MAINTENANCE
Use only mild soap and damp cloth to clean the vac. Never let any liquid get inside the vac; never immerse any part of the vac into a liquid.
NOTE: Make sure the vacuum is completely dry before using it.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium 
battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at 
the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel-cadmium batteries. Help protect our environment and conserve natural resources by returning the spent nickel-cadmium battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call
1-800-8-BATTERY.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under “Tools—Electric” or call: 1-800-544-6986.
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under “Tools-Electric” in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.
| Imported by | See ‘Tools-Electric’ |
| Black & Decker (U.S.) Inc., |
| – Yellow Pages – |
| 701 E. Joppa Rd. |
| for Service & Sales |
| Towson, MD 21286 U.S.A. |
| |
MODE D’EMPLOI
N° de catalogue CHV7200, CHV9600, CHV9610, CHV9650, CHV1200, CHV1400, CHV1410, CHV1450, CHV1560
MERCI D’AVOIR CHOISI BLACK & DECKER !
VISITEZ WWW.BLACKANDDECKER.COM/NEWOWNER
POUR ENREGISTRER VOTRE NOUVEAU PRODUIT.
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
1-800-544-6986
AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LAPLUPART
DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR
TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS
IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.
CONSERVER CE MODE D’EMPLOI POUR UN USAGE ULTÉRIEUR.
IMPORTANTES MISES EN GARDE
Lorsqu’on utilise un appareil électrique, il faut toujours respecter certaines règles de sécurité fondamentales, notamment les suivantes.
LIRE ET COMPRENDRE TOUTES LES DIRECTIVES AVANT D’UTILISER L’APPAREIL.
AVERTISSEMENT : Certaines poussières domestiques contiennent des produits chimiques reconnus par l’État de la Californie comme étant cancérogènes et pouvant entraîner des anomalies congénitales et d’autres risques pour la reproduction tels que l’amiante et le plomb contenu dans les peintures au plomb.
AVERTISSEMENT : Afin de minimiser les risques d’incendie, de secousses électriques ou de blessures.
•Exercer une étroite surveillance lorsqu’on utilise l’appareil près d’un enfant ou que l’appareil est utilisé par ce dernier. Il ne s’agit pas d’un jouet.
•Afin d’éviter les risques de secousses électriques, ne pas immerger l’appareil ni son chargeur.
•Ne pas se servir d’un aspirateur portatif Dustbustermd pour déchets secs afin d’aspirer des liquides, des substances toxiques, des liquides inflammables ou combustibles (de l’essence, par exemple), ni s’en servir dans un endroit renfermant de tels produits.
•Ne pas se servir de l’appareil en présence de vapeurs explosives ou inflammables.
•Ne pas utiliser un appareil dont le cordon ou le chargeur est endommagé, ni un appareil qui ne fonctionne pas bien, qui est tombé, endommagé, resté à l’extérieur ou a été immergé. Le confier à un centre de service autorisé.
•Ne pas utiliser un aspirateur portatif Dustbustermd pour déchets secs à l’extérieur ni sur des surfaces mouillées.
•Manipuler le cordon avec soin. Ne jamais transporter le chargeur ni le socle par le cordon ni tirer sur le cordon pour le débrancher. Saisir plutôt la fiche et tirer dessus. Éloigner le cordon des surfaces chaudes. Ne pas tirer sur le cordon lorsqu’il est autour d’un coin ou d’un rebord tranchant.
•Ne pas laisser pendre le cordon d’une table ou d’un comptoir, ni le laisser entrer en contact avec une surface chaude. Placer ou installer l’appareil loin des éviers ou des surfaces chaudes.
•Ne pas utiliser de cordon de rallonge. Brancher le chargeur directement dans une prise.
•Brancher le chargeur seulement dans une prise standard (120 V, 60 Hz).
•Ne pas utiliser le chargeur avec un autre appareil; ni tenter de charger le produit avec un autre chargeur. Utiliser seulement le chargeur fourni par le fabricant.
•Éloigner les cheveux, les vêtements amples et les membres du corps des orifices et des pièces mobiles de l’appareil.
•Ne pas installer d’accessoires lorsque l’appareil fonctionne.
•Ne pas manipuler la fiche ni l’appareil avec les mains mouillées.
•Ne pas insérer d’objets dans les ouvertures de l’appareil. Ne pas utiliser l’appareil lorsqu’une de ses ouvertures est bloquée. Enlever la poussière, la charpie, les cheveux et toute autre matière susceptible de réduire le débit d’air.
•Ne pas se servir de l’appareil pour aspirer des substances en combustion, comme des mégots allumés, des allumettes ou des cendres chaudes provenant d’un foyer.
•Ne pas utiliser l’appareil sur des surfaces chaudes ni près de celles-ci.
•Faire preuve de prudence lorsqu’on nettoie les escaliers.
•L’appareil est conçu pour une utilisation domestique seulement et non industrielle ou commerciale.
•Utiliser l’appareil seulement de la manière décrite dans le présent guide. Utiliser seulement les accessoires recommandés par le fabricant.
•Débrancher le chargeur avant de le nettoyer ou d'en faire l'entretien.
•L’appareil renferme des piles rechargeables au nickel-cadmium. Ne pas incinérer les piles. La chaleur des flammes peut les faire exploser.
•Il peut se produire une légère fuite du liquide excitateur des piles dans des conditions extrêmes. Toutefois, si ce liquide (solution d’hydrogène de potassium à 20-35 p. 100) atteint la peau, il faut : 1) laver immédiatement à l’eau et au savon ou 2) neutraliser à l’aide d’un acide doux comme du jus de citron ou du vinaigre. Si le liquide excitateur atteint les yeux, rincer immédiatement à l’eau claire pendant au moins dix minutes et consulter un médecin.
•Le chargeur fourni avec ce produit est correctement branché s’il est orienté en position verticale ou au plancher.
CONSERVER CES DIRECTIVES.
Composants (fig. A)
1. | Interrupteur à glissière | 5. | Chargeur |
2. | Bouton de dégagement du bac | 6. | Témoin de chargement |
3. | Bac à poussière | 7. | Roue de nettoyage du filtre |
4. | Socle de chargement mural | | |
