Billy Goat DL1800V, DL2500S owner manual Periodic Maintenance

Page 12

DL Owner’s Manual

MAINTENANCE

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation

Every use

Every 5 hours (daily)

Every 10 Hours

Every 25 Hours

 

 

 

 

 

Inspect for loose, worn or damaged parts.

 

z

 

 

 

 

 

 

 

Check engine oil and air filter

z

 

 

 

 

 

 

 

 

Clean hose

z

 

 

 

 

 

 

 

 

Engine (See Engine Manual)

 

 

 

 

 

 

 

 

 

Inspect battery for damage or leak

 

 

z

 

 

 

 

 

 

Keep engine free of debris

z

 

 

 

 

 

 

 

 

Check battery terminal for corrosion

 

 

 

z

 

 

 

 

 

Check for excessive vibration

 

z

 

 

 

 

 

 

 

IMPELLER REMOVAL

1.Wait for engine to cool and disconnect spark plug wires from the both sides of the engine.

2.Disconnect the negative battery cable (black) (item 12) from the battery.

3.Remove the hose from the unit.

4.Unattach the hose from boom assembly.

5.Remove the intake housing assembly (item 33) using 9/16" socket and socket wrench to remove (12) locknuts (item 47). Be careful to place intake assembly to the side without putting excess strain on safety switch wire harness

6.Remove impeller bolt and lock washer using 5/8" socket and impact wrench (see fig. 6).

7.Once bolt is removed impeller should slide out freely. If impeller will not slide free on crankshaft, obtain a 3/4"-16 x 3" bolt and thread it into the nut that is welded onto the center of the impeller and tighten slowly to push the impeller off the crankshaft.

Note: The 3/4"-16 x 3" bolt can be ordered from your local Billy Goat Dealer (part no. 440192).

8.When impeller is free of the engine shaft, align impeller with the opening and pull it straight out of the housing.

9.Using a new impeller bolt, washer, and lock washer, install new impeller in reverse order. Note: Be sure spacer is in place behind impeller before tightening.

10.Tighten impeller bolt. Torque impeller bolt to [60 Ft. Lbs. (81.4 N.m)].

11.Repeat steps 2 through 5 in reverse order.

12.Reinstall spark plug wires.

Fig. 6

INTERLOCK SYSTEM

With hose coupler installed (as shown in Fig. 8) the switch is open & engine is not grounded out, allowing engine to run.

Fig. 8

BRIGGS WIRING DIAGRAM

Part No 791098

SUBARU WIRING DIAGRAM

12

Hose must be installed and switch lever must engage switch for engine to start.

Form No F070207A

Image 12
Contents Intake ExhausttrailerContents About this ManualSpecifications Serial Plate DataGeneral Safety Instructions and Symbols Page Sound Vibration DataIntended USE Instruction Labels Engine Labels Vanguardsubaru Engine ControlsPacking Checklist Parts BAG Literature AssyAssembly OperationMounting Main unit Adjusting Hose Boom Maintenance Periodic MaintenanceTroubleshooting Warranty Claim ProcedureParts Drawing DL Parts List PartMaintenance Record
Related manuals
Manual 16 pages 18.17 Kb

DL1800V, DL2500S specifications

The Billy Goat DL2500S and DL1800V are powerful and efficient debris loaders, designed to tackle tough landscaping and yard maintenance jobs with ease. Billy Goat has a longstanding reputation for producing high-quality outdoor equipment, and these models exemplify that commitment to excellence.

The DL2500S is equipped with a robust 25 hp engine, providing impressive suction power to efficiently collect and transport leaves, grass clippings, and other debris from yards and gardens. Its innovative design includes a unique impeller system that maximizes airflow, enhancing the loader’s overall efficiency. The machine features a large capacity collection bag, capable of holding up to 2500 pounds of material, which minimizes downtime caused by frequent emptying. Additionally, the DL2500S boasts a heavy-duty steel construction, ensuring durability even under harsh working conditions.

On the other hand, the DL1800V offers a slightly smaller but equally powerful alternative with an 18 hp engine. This model is particularly suitable for residential and light commercial applications, where maneuverability and efficiency are key. The DL1800V is designed with a compact chassis, allowing for easy transport and storage, while still delivering strong sucking power to gather large quantities of debris quickly. It features a shredding capability that reduces the volume of collected debris, making it easier to manage and dispose of.

Both models utilize advanced technologies such as variable speed control, which allows operators to adjust the suction strength based on the conditions of the debris and terrain. This feature enhances versatility, making these loaders effective in a variety of lawn care applications. Moreover, the user-friendly controls ensure that even those with limited experience can operate them efficiently.

Another key characteristic of the Billy Goat DL2500S and DL1800V loaders is their maintenance-friendly design. Easy access points for routine checks and servicing mean that owners can keep their equipment in top working condition without hassle.

In summary, the Billy Goat DL2500S and DL1800V models stand out in the market for their powerful performance, efficient design, and user-friendly features. Whether for professional landscapers or dedicated homeowners, these debris loaders represent a reliable solution for keeping outdoor spaces clean and tidy. With their robust build and advanced technology, they are ideal assets for any landscaping operation.