Electrolux 5995615357 installation manual Intake, 75mm orSlope vent, Exhaust

Horizontal Vent Termination- 3" (75m) Concentric PVC/CPVC Termination

G The concentric termination may be shortened,

but not lengthened from its original factory

supplied length.

3" (75mm) or

Hanger

The concentric termination may only be used

4" (100mm)

Straps

1" (25mm) to

for horizontal terminations.

Intake*

Strap

4" (100mm)

G 3" (75mm) or 4" (100mm) PVC or CPVC pipe

may be used with the concentric termination.

Maintain the same vent pipe diameter from the

3" (75mm) orSlope vent

Insert Bird Screen ***

water heater flue to the termination.

in End of Termination

G Do not exceed the maximum vent lengths as

4" (100mm)

Upwards

*** Not supplied with

Exhaust*

water heater,

specified in this section.

order separately.

G When using 4" (100mm) pipe, it will be necessary

to use 4" (100mm) x 3" (75mm) reducing couplings

and a short section of 3" (75mm) pipe to connect to

the termination.

Use no more than a 6" (150mm) section of pipe to

make the connection between the reducing

couplings and the termination.

G There must be a 1" (25mm) to 4" (100mm) clearance

* 4" (100mm) pipe requires the use of a reducing coupling

between the outside wall and the air intake section

just prior to the termination.

of the termination as illustrated on the left.

No. of

3" (75mm) PVC or CPVC

4" (100mm) PVC or CPVC

G Install a securing strap to prevent movement of

the termination.

Elbows

Max. Straight Vent Length**

Max. Straight Vent Length**

G Terminate at least 12" (300mm) above grade or

4

N / A

N / A

above snow line.

3

16'

(4.8m)

30' (9.0m)

G Terminate at least 7' (2.1m) above a public walkway,

2

22'

(6.6m)

36' (10.8m)

6' (1.8m) from the combustion air intake of any

1

28'

(8.4m)

42' (12.6m)

appliance, and 3' (0.9m) from any other building

opening, gas utility meter, service regulator etc.

** Not including the concentric termination

G Terminate at least 3' (0.9m) above any forced air

inlet within 10' (3m), 1' (0.3m) below, 1' (0.3m)

horizontally from or 1' (0.3m) above any door,

Maximum Vent Length Adjustment Dip switches.

window, or gravity air inlet into any building per

National Fuel Gas Code ANSI Z223.1/NFPA 54.

<Maximum Vent Length and Reduced Input Configurations> G Slope the horizontal vent 1/4" upwards for every

4” Pipe

12" (300mm).

Vent length***

Elbows

G Use a condensation drain if necessary.

G In the Commonwealth of Massachusetts a carbon

ft

m

Number of

0

1

2

3

monoxide detector is required for all side wall

pieces****

horizontally vented gas fuel equipment.

0

0.00

0

N /A

3

0%

3 0%

4 -3%

Please refer to Technical Bulletin TB 010606 for full

3

0.90

1

N /A

3

3 -3%

4

installation instructions.

6	1.80	2	N /A	3	4 -3%		4
9	2.70	3	N /A	3 -3%	4		4
12	3.60	4	N /A	4 -3%	4		4
15	4.50	5	N /A	4	4		4
18	5.40	6	N /A	4	4		4
21	6.30	7	N /A	4	4		4
24	7.20	8	N /A	4	4		4
27	8.10	9	N /A	4	4		4
30	9.00	10	N /A	4	4		4 -5%
33	9.90	11	N /A	4	4
								3 Short length using 4" (100mm) pipe
36	10.80	12	N /A	4	4	-5%
								4 Long length using 4" (100mm) pipe
39	11.70	13	N /A	4
								****Table assumes straight vent pieces are 3’ (0.9m) each.
42	12.60	14	N /A	4 -5%
								Shorter or longer vent pieces may also be used up to the maximum
								allowed vent length.

*** Refer to page 13 for 3" pipe Maximum Vent Length Adjustment Dipswitches table.