American Dryer Corp GWH 425 EF Mounting Installation, Incandescent Particle Tray Illustration

Page 7

MOUNTING INSTALLATION

The 425 EF is design certified for mounting on a wall. Secure the two L shaped hooks, which are provided with heater, to a wall surface. Place them 13 ¼” apart as shown in Fig 2.

Do not install this appliance on a carpeted wall or over floor covering which is combustible, such as carpet. The heater must be mounted on a wall using appropriate anchoring materials. If wall is a stud wall sheathed with plasterboard, it is recommended that support board(s) either 1x4’s or 1/2" (minimum) plywood first be attached across a pair of studs and then the heater should be attached to the support boards. See Fig 2.

NOTE: Additionally the 425 EF should be spaced away from any combustible wall surface to provide the necessary clearance that the venting material specifies must be maintained between the vent pipe and a combustible surface. See VENTING section. Also, review the FXHOOD horizontal vent terminator instruction sheet (provided with the FXHOOD) prior to installation.

In earthquake-prone zones, CEC recommends that installers use a large washer and lag screw through the existing holes used to hang the heater to affix the upper third of the heater to the mounting board. To affix the lower third of the heater, CEC recommends that two new holes be drilled in the heater’s frame, each one 16 inches below the top two holes, and that washers and lag screws be used to secure the lower portion of the heater to a spacing board.

Expansion and contraction of piping due to changing water temperature in the pipes imparts movement to the heater which, if mounted directly to a brittle, friable board, such as plasterboard, can cause failure of mounting.

The incandescent particle tray (shipped loose in the carton with the water heater) must be attached at the bottom of the water heater front cover at the time of installation. Use the screws provided. See figure 3.

SCREWS

INCANDESCENT PARTICLE TRAY

Fig. 3 - Incandescent Particle Tray Illustration

13 ¼”

WALL STUDS

SUPPORT BOARD

1” X 4”

SPACE BOARD

Fig. 2 - Mounting the Heater

6 720 607 017

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents GWH 425 EF Table of Contents For Your SafetyWhat to do if YOU Smell GAS Unpacking the 425 EF Heater FeaturesTOP a Front B Back Sides Floor C Vent Diameter Front View Side ViewGeneral Rules to Follow For Safe Operation Proper Location for Installing Your HeaterClearances Combustion AIR RequirementsIncandescent Particle Tray Illustration Mounting InstallationInch VentingHorizontal Side Wall Soffit GAS Line Sizing GAS ConnectionsGAS Line Sizing For Natural GAS GAS PIPING, ConnectionsFor LP GAS Water Connections Water valve and water connectors, top viewElectrical Connections Flue gas safety deviceLighting and Operating Instructions For Your Safety Read Before Operating Your HOT Water HeaterTemperature Adjustment Knob No Spark AT the Pilot Microswitch adjustmentPilot Sparks Continuously with no Water Running FAN Circulates When HOT Water is Shut OFF 720 607 Diagram of 425 EF Interior Components Diagram and Parts List Interior Components Diagram Parts List 425 EF Flow chart of 425 EF Fifteen Year Limited Warranty Controlled Energy Corp Maintenance Table see

GWH 425 EF specifications

American Dryer Corp GWH 425 EF is a highly efficient, energy-saving dryer designed specifically for commercial laundry applications. With its robust construction and innovative technologies, the GWH 425 EF delivers exceptional performance while maximizing operational efficiency.

One of the main features of the GWH 425 EF is its optimized drying capacity. With a 45-pound load capacity, this dryer efficiently processes large volumes of laundry, making it an ideal choice for laundromats, hotels, and other commercial establishments. The dryer is designed to handle varied fabric types, providing versatile solutions for all drying needs.

The GWH 425 EF incorporates advanced heating technologies that enhance drying speed and efficiency. Its energy-efficient gas heating system not only reduces operation costs but also minimizes environmental impact. The dryer offers a range of adjustable temperature settings, enabling operators to customize drying cycles for different fabric types and load sizes. This flexibility enhances fabric care and improves overall drying performance.

Another standout characteristic of the GWH 425 EF is its user-friendly control panel. Equipped with a digital display, the control panel allows for easy programming and monitoring of drying cycles. Operators can select from multiple drying options, and the machine's intuitive interface makes it simple to adjust settings quickly. This convenience translates to improved workflow and increased productivity in busy commercial environments.

Safety is a top priority for American Dryer Corp, and the GWH 425 EF is equipped with multiple safety features. These include a built-in lint screen that traps lint and debris, reducing the risk of fires. Additionally, the dryer is engineered with a robust structural design, ensuring durability and longevity even under constant use.

The GWH 425 EF is also designed with maintenance in mind. It features easy access to internal components for routine servicing, allowing operators to keep the dryer in peak operating condition with minimal effort. This eases maintenance burdens and prolongs the lifespan of the machine.

Finally, the GWH 425 EF is backed by American Dryer Corp's commitment to quality and customer satisfaction. With a reputation for producing reliable and efficient laundry equipment, American Dryer Corp ensures that the GWH 425 EF meets the demanding needs of commercial laundry services. Overall, the American Dryer Corp GWH 425 EF is an excellent investment for businesses looking to optimize their laundry operations while maintaining quality and efficiency.
Top Page Image Contents