A.O. Smith AOSRE50400 warranty For Your Information, Thermal Expansion, Operational Conditions

Page 13

FOR YOUR INFORMATION

THERMAL EXPANSION

“AIR” IN HOT WATER FAUCETS

Water supply systems may, because of such events as high line pressure, frequent cut-offs, the effects of water hammer among others, have installed devices such as pressure reducing valves, check valves, back flow preventers, etc. to control these types of problems. When these devices are not equipped with an internal by-pass, and no other measures are taken, the devices cause the water system to be closed. As water is heated, it expands (thermal expansion) and closed systems do not allow for the expansion of heated water.

The water within the water heater tank expands as it is heated and increases the pressure of the water system. If the relieving point of the water heater’s temperature-pressure relief valve is reached, the valve will relieve the excess pressure. The temperature-pressure relief valve is not intended for the constant relief of thermal expansion. This is an unacceptable condition and must be corrected. It is recommended that any devices installed which could create a closed system have a by-pass and/or the system have an expansion tank or device to relieve the pressure built by thermal expansion in the water system. Expansion tanks are available for ordering through a local plumbing contractor. Contact the local water heater supplier or service agency for assistance in controlling these situations.

STRANGE SOUNDS

Possible noises due to expansion and contraction of some metal parts during periods of heat-up and cool-down do not necessarily represent harmful or dangerous conditions.

Operational Conditions

Water odor

In each water heater there is installed at least one anode rod (see parts sections) for corrosion protection of the tank. Certain water conditions will cause a reaction between this rod and the water. The most common complaint associated with the anode rod is one of a “rotten egg smell” in the hot water. This odor is derived from hydrogen sulfide gas dissolved in the water. The smell is the result of four factors which must all be present for the odor to develop:

A.A concentration of sulfate in the supply water.

B.Little or no dissolved oxygen in the water.

C.A sulfate reducing bacteria which has accumulated within the water heater (this harmless bacteria is nontoxic to humans).

D.An excess of active hydrogen in the tank. This is caused by the corrosion protective action of the anode.

Smelly water may be eliminated or reduced in some water heater models by replacing the anode(s) with one of less active material, and then chlorinating the water heater tank and all hot water lines. Contact the local water heater supplier or service agency for further information concerning an Anode Replacement Kit and this chlorination treatment. If the smelly water persists after the anode replacement and chlorination treatment, we can only suggest that chlorination or aeration of the water supply be considered to eliminate the water problem.

Do not remove the anode leaving the tank unprotected. By doing so, all warranty on the water heater tank is voided.

HYDROGEN GAS: Hydrogen gas can be produced in a hot water system that has not been used for a long period of time (generally two weeks or more). Hydrogen gas is extremely flammable and explosive. To prevent the possibility of injury under these conditions, we recommend the hot water faucet, located farthest away be opened for several minutes before any electrical appliances which are connected to the hot water system are used (such as a dishwasher or washing machine). If hydrogen gas is present, there will probably be an unusual sound similar to air escaping through the pipe as the hot water faucet is opened. There must be no smoking or open flame near the faucet at the time it is open.

HIGH WATER TEMPERATURE SHUT OFF SYSTEM

A non-adjustable high temperature limit control operates before steam temperatures are reached. The high limit switch must be reset manually when it operates. BECAUSE THE HIGH LIMIT OPERATES ONLY WHEN ABNORMALLY HIGH WATER TEMPERATURES ARE PRESENT, IT IS IMPORTANT THAT A QUALIFIED SERVICE AGENT BE CONTACTED TO DETERMINE THE REASON FOR OPERATION BEFORE RESETTING .

•Turn off and unplug the water heater. Do not attempt to reset thermostat with power on.

•Remove the front panel, see “Removing Front Panel” in the Periodic Maintenance section.

•Remove the insulation to expose the reset button.

•Reset the high limit by pushing in the red button.

•Replace the insulation so that it completely covers the thermostat and element.

•Replace the front panel.

•Plug in and turn on the water heater.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Residential Electric Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsHotter Water can Scald Typical Installation Mixing Valve UsageLocating the NEW Water Heater Read ALL Instructions Before Using this Water HeaterFacts to Consider About the Location Insulation BlanketsMounting Installing the NEW Water HeaterWater Piping Water Piping Pressure Test Temperature- Pressure Relief ValveFilling the Water Heater Wiring Diagram Wiring Temperature Adjustment Temperature RegulationThermal Expansion For Your InformationOperational Conditions Temperature-Pressure Relief Valve Operation Periodic MaintenanceAnode ROD Inspection DrainingElement Cleaning / Replacement Thermostat Removal / ReplacementReplacement RemovalService High Limit Switch Removal and replacementTo Remove and Replace Anode Leakage Checkpoints Problem Possible Causes Corrective Action Troubleshooting GuidelinesRepair Parts List Conditions and Exceptions Residential Electric WarrantyClaim Procedure Service and Labor ResponsibilityLimitation on Implied Warranties DisclaimersPage

AOSRE50400 specifications

A.O. Smith AOSRE50400 is a high-efficiency water heater that exemplifies advanced technology and engineering, making it a popular choice for residential and commercial applications. This model is part of A.O. Smith’s comprehensive line of water heating solutions and is designed to provide reliable performance while maximizing energy efficiency.

One of the standout features of the AOSRE50400 is its high energy factor (EF), which greatly contributes to reduced energy bills and a smaller environmental footprint. With an EF rating of approximately 0.95, this water heater utilizes innovative design techniques to ensure that more of the energy consumed is converted into usable hot water. It meets and often exceeds the stringent energy efficiency standards set by the Department of Energy.

The AOSRE50400 is equipped with advanced insulating materials, which minimize heat loss and improve overall efficiency. This is particularly beneficial in maintaining water temperature for extended periods, reducing the need for excessive reheating. The tank has been designed with a glass-lined interior that offers enhanced durability and resistance to corrosion, extending the lifespan of the unit.

Another important characteristic of the AOSRE50400 is its large capacity. With a tank size of 50 gallons, it can effectively meet the hot water demands of medium to large households or businesses. This capacity allows for simultaneous usage across multiple outlets, ensuring that you never run out of hot water when you need it most.

The digital display and user-friendly interface provide homeowners with easy control over temperature settings and operation modes. This feature enhances user convenience and allows for customized hot water delivery that can cater to specific usage needs. Furthermore, the built-in diagnostic system alerts users to any potential issues, ensuring timely maintenance and reducing the risk of costly repairs.

A.O. Smith also prioritizes safety in the design of the AOSRE50400. It comes with multiple safety features, including a temperature and pressure relief valve, which helps prevent potential overpressure situations. This commitment to safety ensures peace of mind for users and compliance with local plumbing codes.

In summary, the A.O. Smith AOSRE50400 water heater exemplifies modern engineering and technology, offering high energy efficiency, a durable design, user-friendly controls, and a strong commitment to safety. Its large capacity and advanced features make it an exceptional choice for those seeking reliable and efficient hot water solutions.
Top Page Image Contents