A.O. Smith SDV, FDVT owner manual

Page 14

9. Slide the 6” telescoping vent section apart to reveal the beads.

NOTE: The section of 6” pipe with beads will connect to the elbow. Using the caulking supplied, fill the beads.

FIGURE 57

5.Making sure the 6” diameter elbow is centered around the 3” diameter flue, secure the 6” diameter vent pipe using four sheet metal screws at the connection of the jacket top.

FIGURE 58

6.The standard kit includes a single piece of 3” flue and 6” vent pipe which will not be used in conjunction with the horizontal kit.

FIGURE 59

7.Slide the vent collar (to be installed later) over the 6” vent elbow.

FIGURE 60

8.Place the water heater at the opening in the wall, at the predetermined clearance.

FIGURE 62

10. Insert the 6” telescoping vent section into the wall.

FIGURE 63

11.Move outdoors with all the remaining vent parts. Using the tube of sealant supplied, run an ample amount on the inside surface of the collar assembly that will contact the exterior wall and also fill the bead on the end of the 6” diameter vent collar.

FIGURE 64

12.Install the vent collar assembly through the wall, connecting it to the 6” telescoping extension. Remember, the extension is not connected yet and it may be necessary to go back indoors and push it back up for a tight fit to the collar.

FIGURE 65

13.Four wood screws are supplied to temporarily attach the collar to the exterior wall to the building. However, other types of screws may have to be substituted depending on the construction of the exterior wall.

FIGURE 61

FIGURE 66

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents FDV/FDVT/SDV Typical Installation Replacement PartsGeneral Safety Information InstallationGAS Connections Water Potable Heating and Space HeatingClosed Water System Vent Pipe Termination Relief ValveVenting Combustion AIR and VentilationFlue Extensions Optional Wire GrillVenting Clearances Horizontal Extension KIT Possible Extension CombinationsVertical Extension KIT Height Equation D + G = EWater Heater Attitude ALL InstallationsCutting the Opening Through Outside Wall Page ANY Optional Vent KIT Equation C a -10 = GallonPage Optional Horizontal Vent KIT #900124-7 Installation #3 Page Page Equation C a 10 = Page Filling High Altitude InstallationsOperation For Your Safety Read Before Lighting Lighting InstructionsPilot and Main Burner MaintenanceTemperature Regulation Draining Temperature & Pressure Relief ValveAnode ROD Maintenance CondensationTroubleshooting Conditions and Exceptions Service and Labor ResponsibilityClaim Procedure Limitation on Implied WarrantiesTH STREET, ALSIP, IL Phone 1-800-433-2545 FAX

SDV, FDVT, FDV specifications

A.O. Smith is a leading name in the water heating industry, known for its innovative products and commitment to quality. Among its extensive lineup, the FDV, FDVT, and SDV series stand out due to their advanced features and technologies designed to enhance performance and efficiency.

The FDV series represents a revolution in traditional water heating solutions. These direct vent water heaters are designed to provide hot water on demand while minimizing energy consumption. The FDV models utilize a dual venting system, allowing for the efficient expulsion of combustion gases outside the home while drawing in fresh air for the combustion process. This design increases efficiency by ensuring optimal combustion and improves safety by reducing the risk of indoor air contamination.

The FDVT series builds upon the innovative features of the FDV, integrating a tankless design that provides unlimited hot water. This makes it an ideal choice for households with higher hot water demands. The FDVT models use high-efficiency burners and advanced heat exchangers to deliver hot water quickly and consistently, adapting to varying flow rates. They are also equipped with intelligent control systems that monitor water usage patterns and adjust operation accordingly, optimizing energy efficiency without sacrificing performance.

The SDV series caters to those looking for a reliable and efficient storage tank water heater. With a robust construction and reliable design, these water heaters are built to last. The SDV models are designed with high-quality insulation to minimize heat loss, making them energy-efficient options for storing hot water. Additional features include built-in safety mechanisms, such as temperature and pressure relief valves, ensuring safe operation at all times.

A.O. Smith's commitment to innovation is evident in their use of cutting-edge technologies across these series. Both the FDV and FDVT models incorporate sophisticated electronic controls, enabling features like scheduling and remote access for greater convenience. They are compatible with smart home systems, allowing users to monitor and manage water heating remotely.

In terms of energy efficiency, models within these series are designed to exceed industry standards, often qualifying for energy rebates and incentives in various regions. With features such as modulating burners, they adjust the energy input based on demand, significantly reducing operational costs.

Overall, A.O. Smith's FDV, FDVT, and SDV series represent leading-edge solutions in water heating, combining efficiency, safety, and advanced technology to meet the diverse needs of modern households. Whether seeking endless hot water or reliable storage solutions, these series offer unparalleled options that prioritize performance and sustainability.
Top Page Image Contents