Fasten Door Bracket | Chamberlain 2000UK manual

FASTEN DOOR BRACKET – 18

If yours is a canopy or dual-track style garage door, a door arm conversion kit is required. Follow the installation instructions included with the replacement door arm. Exercise care in removing and assembling arm conversion kit. Keep fingers away from the sliding parts.

Sectional and One-Piece Door Installation Procedure:

1.Center bracket (1) at the top of inside face of door as shown. Mark holes.

2.A. Wooden doors

Drill 8mm (5/16") holes and fasten the door bracket with nut, lock washer, and carriage bolt (2).

B. Sheet metal doors

Fasten with sheet metal screws (3).

C. One-piece door optional

Fasten with sheet metal screws (3).

CONNECT DOOR ARM TO TROLLEY – 19

Sectional Door Installation: Note door arm configuration in Figure B.

One-Piece Door Installation: Procedure (Figure A).

Connect straight door arm (1) and curved door arm sections (2) to obtain the longest possible length with hardware (3, 4 & 5). With door closed, connect straight door arm section to door bracket with a clevis pin (6). Secure with a ring fastener (7).

Before connecting door arm to trolley, adjust travel limits. Limit adjustment screws are located on left side panel.

Open Door Adjustment: Decrease up limit. Turn up limit adjustment screw counterclockwise 5-1/2 turns.

Press door control button. Trolley will travel to full open position (8). Manually raise door to open position (parallel to floor) and lift door arm (9) to trolley. The arm should touch trolley just in back of door arm connector hole (10) as shown in solid line drawing. Increase up limit if necessary. One full turn equals 5cm (2") of door travel.

Closed Door Adjustment: Decrease down limit. Turn down limit adjustment screw clockwise 5 complete turns.

Press door control button. Trolley will travel to full closed position (11). Manually close door and lift door arm (12) to trolley. The arm should touch trolley just ahead of door arm connector hole (13) as shown in dotted line drawing. Decrease down limit if necessary. One full turn equals 5cm (2") of door travel.

Connect Door Arm to Trolley: With door closed, connect curved arm to trolley with remaining clevis pin. Secure with ring fastener.

Note: Lift door slightly to make connection if necessary.

Run opener through a complete travel cycle. If door has a slight "backward" slant in full open position, decrease up limits until door is parallel to floor.

PROGRAM YOUR OPENER & REMOTE –	20
Activate the opener only when door is in full view, free of
obstruction and properly adjusted. No one should enter or leave
garage while door is in motion. Do not allow children to operate
push button(s) or remote(s). Do not allow children to play near
the door.
Your garage door opener receiver and remote control transmitter are
set to a matching code. If you purchase additional remote controls, the
garage door opener must be programmed to accept the new remote
code.
Program the Receiver to Match Additional Remote Control Codes
1. Press and hold the remote control push button (1).		-GB
2. Press and release the "Smart" button (2) on the back panel
		4
of the opener. The opener light will flash once.

3. Release the remote push button.
Now the opener will operate when the remote control push button is
pressed.
If you release the remote control push button before the opener
light flashes, the opener will not accept the code.
To Erase all Remote Control Codes

•Press and hold the "Smart" button on the opener panel until the indicator light turns off (about 6 seconds). All the codes the opener has learned will be erased.

•To reprogram, repeat Steps 1 – 3 for each remote control in use.

ADJUSTMENT SECTION 21 – 23

LIMIT ADJUSTMENT – 21

Run the opener through a complete travel cycle. Limit adjustments are not necessary when the door opens and closes completely and doesn't reverse unintentionally in the fully closed position.

Situations requiring limit adjustment are listed below. Run the opener through a complete travel cycle after each adjustment.

Note: Repeated operation of the opener during adjustment procedures may cause motor to overheat and shut off. Allow a 15 minute cooling period after 5 continuous operations of the opener.

Read the following carefully before proceeding to Force Adjustment. Use a screwdriver to make limit adjustments.

If Door Doesn't Open Completely but Opens at Least 1,5m

( 5 feet): Increase up travel. Turn the up limit adjustment screw (1) clockwise. One turn equals 5cm (2") of travel.

If door does not open at least 1,5m (5 feet): Adjust up (open) force. See Force Adjustment.

If Door Doesn't Close Completely:If door arm is at maximum length, increase down travel. Turn down limit adjustment screw (2) counterclockwise. One turn equals 5cm (2") of travel.

If the door still will not close completely, the header bracket is positioned too high.

If Opener Reverses in Fully Closed Position: Decrease down travel. Turn down limit adjustment screw (2) clockwise. One turn equals 5cm (2") of travel.

If Door Reverses when Closing and there is no Interference to Travel Cycle: Test door for binding. Pull manual release handle. Manually open and close door. If door is binding, call a door serviceman. If door is not binding or unbalanced, adjust down (close) force.

2000UK specifications

The Chamberlain 2000UK is a cutting-edge garage door opener that combines advanced technology with user-friendly features to enhance convenience and security for homeowners. Designed specifically for the UK market, this model boasts a range of attributes that make it a standout choice in the realm of residential automation.

One of the primary features of the Chamberlain 2000UK is its Quiet Drive technology. This innovative system ensures that the operation of the garage door is incredibly silent, making it ideal for homes with bedrooms located above or adjacent to the garage. The belt-driven motor operates smoothly and quietly, minimizing noise pollution—a significant advantage for those living in close quarters with neighbors.

Another notable characteristic of the Chamberlain 2000UK is its Smartphone Connectivity. Leveraging smart home technology, users can monitor and control their garage door from anywhere using the MyQ app. This feature not only provides convenience but also enhances security, as homeowners can check the status of their door remotely, receive notifications if the door is left open, and even grant access to guests when they’re not home.

In terms of security, the Chamberlain 2000UK is equipped with enhanced safety features. The integrated security encrypted code technology prevents unauthorized access by ensuring that only the synchronized remote controls can operate the garage door. A built-in safety sensor also reverses the door's motion if it detects an obstruction, reducing the risk of accidents and injuries.

The installation process of the Chamberlain 2000UK is designed to be straightforward and user-friendly. The system is compatible with most traditional garage doors, and the product includes comprehensive instructions, enabling many users to set it up without professional assistance. Moreover, the compact design of the motor unit allows for installation in tight spaces, while still providing reliable performance.

Energy efficiency is another significant characteristic of the Chamberlain 2000UK. This model is designed to consume minimal power, which is beneficial not only for the environment but also for homeowners looking to reduce their utility bills.

With a combination of features like quiet operation, smartphone integration, advanced security measures, and user-centric design, the Chamberlain 2000UK sets a new standard in the world of garage door openers. It's a perfect choice for anyone looking to modernize their home, adding convenience and peace of mind with every use.