Chamberlain 800A Operation of the Door Control, Model 600A, Using the Multi-Function Door Control

21Install Door Control

Locate door control where the garage door is visible, away from door and door hardware and out of the reach of children. Mount at least 1,5 m (5 feet) above the floor.

Serious personal injury from a moving garage door may result from misuse of opener. Do not allow children to operate the door control or remote control transmitter.

Fasten the caution label permanently to the wall near the door control as a reminder of safe operating procedures.

There are 2 screw terminals (1) on the back of the door control (2). Strip about 6mm (1/4") of insulation from bell wire (4). Separate wires enough to connect the white/red wire to RED terminal screw 1 and the white wire to WHT terminal screw 2.

Fasten the door control to an inside garage wall with sheet metal screws (3) provided. Drill 4mm (5/32") holes and use anchors if installing into drywall. A convenient place is beside the service door and out of reach of children.

Run the bell wire up the wall and across the ceiling to the garage door opener. Use insulated staples to secure wire. The receiver quick connect terminals are located behind the light lens of the opener. Connect the bell wire to the terminals as follows: white/red to red and white to white (5).

Operation of the Door Control

Press to open or close the door. Press again to stop the door while moving.

23

1

3

RED WHT

1 2

		LOCK
			LIGHT
(Models 800A, 1000A)
	1
WHT	2
2
RED
1	1		3
	(Model 600A)
	5
	1	2	3

O–

180 s	60 s
	120 s

6mm

4

22Program your Opener & Remote

Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door.

Your garage door opener receiver and remote control transmitter are set to a matching code. If you purchase additional remote controls, the garage door opener must be programmed to accept the new remote code.

Program the Receiver to Match Additional Remote Control Codes:

Using the orange “LEARN” Button:

1.Press and release the orange “learn” button on the opener. The learn indicator light will glow steadily for 30 seconds (1).

2.Within 30 seconds, press and hold the button on the hand-held remote that you wish to operate your garage door (2).

3.Release the button when the opener light blinks. It has learned the code. If the light bulb is not

installed, two clicks will be heard (3).

Using the Multi-Function Door Control:

1.Press and hold the button on the hand-held remote that you wish to operate your garage door (4).

2.While holding the remote button, press and hold the

LIGHT button on the Multi-Function Door

Control (5). 3. Continue holding both buttons while you press the

push bar on the Multi-Function Door Control (all three buttons are held) (6).

4. Release buttons when the opener light blinks. It has learned the code. If the light bulb is not installed, two clicks will be heard (7).

Now the opener will operate when the remote control

push button is pressed. If you release the remote control push button before the opener light flashes,

the opener has not learned the code.

To Erase all Remote Control Codes:4 To deactivate any unwanted remote, first erase all codes: Press and hold the orange “learn” button on opener until the learn indicator light goes out (approximately 6 seconds). All previous codes are

now erased. Reprogram each remote or keyless entry you wish to use.

3-Channel Remote:

If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any rolling code 3-channel remote or mini-remote can be programmed to operate this or other rolling code garage door openers.

1 2 3

5	6	7
	LOCK
	L IG H T

23Open/Close/Stop Operation

(only if you have a Multifunction door control)

Your remote control can be programmed to operate one door using all 3 buttons: the left button will only open the door, the middle button will only close the door, and the third button will stop the door’s movement. You may set up this feature as follows:

1.With the door closed, press and hold the left remote push button.

2.Press and hold the Lock button on the door control.

3.Press and hold the door control push bar.

Open Close

Stop

When the opener lights flash, release all buttons. Test by pressing the left (Open) button on the remote. The door should open. Press it again while the door is open and nothing should happen. Press the middle (Close) button and the door should close. Press the third (Stop) button while the door is moving and it should stop immediately.

114A2910B-GB	7-GB	8-GB
		114A2910B-GB