Installation Instructions

Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installa- tion. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.

1.The pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.

2.The inlet to the pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of

800 F, it is important to insure a positive head to the pump to prevent cavitation.

3.The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve

between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.

4.Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3 and 6.

5.Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the pump.

NOTE: An anti-sieze material must be applied to the engine cranckshaft to ensure trouble free disassembly of the pump.

Finally, remember that high pressure operation in a pump system has many advantages. But, if it is used carelessly and without regard to its potential hazard, it can cause serious injury.

IMPORTANT OPERATING CONDITIONS

Failure to comply with any of these conditions invalidates the warranty.

1.Crankcase oil should be changed after the first 50 hours of operation. Then at regular intervals of 500 hours or less depending on operating conditions.

Use Giant synthetic oil

2.Pump operation must not exceed rated

pressure, volume, or RPM. A pressure relief device must be installed in the discharge of the system.

3.Acids, alkalines, or abrasive fluids cannot be pumped unless approval in writing is obtained before operation from Giant Industries, Inc.

4.Run the pump dry approximately 10 seconds to drain the water before exposure to freezing temperatures.

NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600

HR3030, HR3025, HR2527A specifications

The Giant HR2527A, HR3025, and HR3030 are advanced tractor models designed to meet the diverse demands of modern agricultural operations. Each model comes with unique features and technologies, making them suitable for various tasks in different farming environments.

Starting with the Giant HR2527A, this compact and versatile tractor is ideal for small to medium-sized farms. One of its main features is its powerful and efficient engine, which offers excellent performance while maintaining low fuel consumption. The HR2527A boasts a user-friendly interface, allowing operators to easily navigate through its functionalities. Its tight turning radius makes it an ideal choice for operations in confined spaces, such as greenhouses or vineyards. Additionally, the hydraulic system is designed for optimal performance, enabling the attachment of various implements, from mowers to loaders.

Moving on to the Giant HR3025, this model provides enhanced power and capabilities, making it suitable for heavier tasks. The HR3025 features a robust chassis and a high torque engine that delivers impressive lifting and pulling capacities. A standout technology in this model is its advanced four-wheel drive system, which ensures exceptional traction and stability, particularly in challenging terrains. Furthermore, the spacious cabin is designed for operator comfort, equipped with ergonomic controls and excellent visibility, which enhances productivity during long working hours.

Lastly, the Giant HR3030 represents the pinnacle of innovation and efficiency in this line-up. Equipped with a powerful turbocharged engine, the HR3030 is specifically constructed for large-scale agricultural tasks that require considerable strength and speed. It features cutting-edge technology, including an intelligent transmission system that optimizes power delivery based on load, ensuring efficiency. The HR3030 also comes with customizable hydraulic options, providing farmers with the flexibility to tailor the tractor to specific requirements. Safety features, such as an advanced braking system and protective cab design, make it a reliable choice for demanding work scenarios.

In summary, the Giant HR2527A, HR3025, and HR3030 are designed to cater to a wide range of agricultural needs. With their powerful engines, advanced technologies, and operator-friendly features, each model offers unique benefits that contribute to increased productivity and efficiency in farming operations. Whether for small farms or extensive agricultural projects, these tractors provide the tools necessary for success.