Installation Instructions

Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installation. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.

1.The pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.

2.The inlet to the pump should be sized for the flow rate of the pump with no unnecessary restrictions

that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to°be operated at temperatures in excess of 1400 F, it is important to insure a positive head to the pump to prevent cavita- tion.

3.The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pres- sure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.

4.Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connections, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further

reduce system pulsation. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the un- loader.

5.Crankshaft rotation on Giant Industries, Inc. pumps should be made in the direction desig- nated by the arrows on the pump crankcase. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the chart on pages 3 & 6.

6.Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the pump.

Finally, remember that high pressure operation in a pump system has many advantages. But, if it is used carelessly and without regard to its potential hazard, it can cause serious injury.

IMPORTANT OPERATING CONDITIONS

Failure to comply with any of these conditions invalidates the warranty

1.Prior to initial operation, add oil to crankcase so that the oil level is between the two lines on the oil dipstick. DO NOT OVERFILL. SAE 80 Indus- trial Gear oil may be used. Crankcase oil should be changed after the first 50 hours of operation, then at regular intervals of 500 hours or less de- pending on operating conditions.

2.Pump operation must not exceed rated

pressure, volume, or RPM. A pressure relief device must be installed in the discharge of the system.

3.Acids, alkalines, or abrasive fluids cannot be pumped unless approval in writing is obtained before operation from Giant Industries, Inc.

4.Run the pump dry approximately 10 seconds to drain the water before exposure to freezing temperatures.

GP7136, GP7132 specifications

The Giant GP7136 and GP7132 are advanced bicycle tires known for their performance, durability, and innovative technologies. These models are specifically designed to cater to the needs of avid cyclists who require reliable and efficient tires for both on-road and off-road adventures.

One of the standout features of the GP7136 and GP7132 is their enhanced grip and traction. The tires are constructed with a specialized rubber compound that provides superior adherence to various surfaces, making them ideal for diverse riding conditions. Whether navigating slick roads or rugged trails, these tires deliver confidence-inspiring traction, allowing cyclists to tackle challenges with ease.

Another notable characteristic of the GP7136 and GP7132 is their puncture resistance. Designed with a robust construction, these tires incorporate layers of protective materials that help prevent flats due to sharp objects like nails or glass. This added durability ensures that cyclists can enjoy longer rides without the worry of sudden punctures, giving them the freedom to focus on their performance.

In terms of comfort, the GP7136 and GP7132 utilize innovative technologies that enhance the riding experience. The tires feature an optimized tread pattern that aids in shock absorption, reducing the impact on the rider when encountering bumps and uneven surfaces. This results in a smoother ride, which is particularly beneficial during long-distance journeys or challenging terrains.

The lightweight design of the GP7136 and GP7132 also contributes to their performance attributes. By minimizing rotational weight, these tires enable quicker acceleration and improved handling, giving cyclists a competitive edge whether they are racing or just enjoying a casual ride.

Both models are available in a variety of sizes to accommodate different bike types, from road bikes to mountain bikes. This versatility ensures that cyclists can find the perfect fit for their specific riding style and preferences.

In summary, the Giant GP7136 and GP7132 stand out in the cycling world thanks to their impressive features such as enhanced grip, puncture resistance, comfort technologies, and lightweight design. These tires are crafted to meet the demands of both competitive cyclists and casual riders, making them an excellent choice for anyone seeking high-quality bicycle tires. With the GP7136 and GP7132, cyclists can expect a reliable, performance-oriented riding experience that allows them to push their limits and enjoy every pedal stroke.