General Description, Installation | Ingersoll-Rand NP322L01-1

GENERAL DESCRIPTION

ARO systems are totally enclosed, sealing the material in the system from air and moisture, preventing premature cure-out of the material. This allows for either continuous or intermittent use of the system and reduces the need for daily system clean-up.

The built-in lift capability allows for quick drum changeover and easy lift- ing of pump assembly from the container.

INSTALLATION

The NP322L( )( )-( ) Chop-Check Dispensing System comes completely assembled. Remove unit from crate and place on a level surface. Install material hose and dispensing device as required.

When the following instructions are observed, heavy paste materials can be pumped directly from their original 5 gallon drum without air inclu- sion, or excessive waste. The follower plate creates an air tight seal as well as clean-wiping action in its progressive downward movement into the drum.

OPERATING INSTRUCTIONS

TO RAISE LIFT:

1.Adjust (turn needle valve knob counter-clockwise) air pressure to lift. Connect the air supply (160 PSI MAX) to the air inlet.

2.Raise the lift high enough to clear the height of the drum. Stop the lift’s upward travel by adjusting (turn needle valve clockwise until tight) needle valve.

3.Check vent plug on follower plate to be sure it easily threads in and out. It is recommended to lubricate the threads of the plug to help prevent possible set up of compound at this point. See 65184X-X Follower Plate Operator’s Manual.

TO LOWER LIFT:

WARNING PINCH HAZARD. Follower can descend quickly causing injury. Keep hands clear when aligning with container.

NOTE: Be certain the Follower Plate vent plug has been removed so that the air trapped between the follower and the material is allowed to escape from this vent. Captured air between the follower plate and drum will escape.

NOTE: The lift may hesitate momentarily before starting downward. The air pressure inside the post air chamber must decrease before it will be- gin to descend.

1.Disconnect air line from the lift air inlet. Adjust (turn needle valve knob counter-clockwise) needle valve to lower the pump end into drum.

2.Replace the vent plug once the material begins to ooze from the vent opening.

3.Adjust (turn pump air regulator knob counter-clockwise to prevent over pressurization of pump) knob on pump air regulator.

4.Connect air line to pump air regulator and adjust (turn pump air regu- lator clockwise) air until pump begins to cycle.

5.Trigger gun to prime pump with material.

TO RAISE LIFT, (NORMAL OPERATION):

1.Disconnect air line from pump air regulator and connect to lift air in- let. Adjust the follower plate air valve pressure up to approximately 8 psig (.55 bar). DO NO OVERPRESSURIZE THE DRUM to avoid damage.

NOTE: Air from this valve will only pass when the unit is being raised.

2.Adjust (turn needle valve knob counter-clockwise) air pressure on lift.

3.Raise the lift high enough to clear the height of the drum. Stop the lift’s upward travel by adjusting needle valve knob counter-clock- wise.

REFER TO PAGE 3:

1.Once lift assembly and pump are in the “UP” position, place and cen- ter an opened 5 gallon drum of material on the lift base. Use the stops on the base to center the 5 gallon drum. Tighten thumb screw to secure drum.

2.Lubricate lower follower wiper plate seal with grease. NOTE: Make certain the grease is compatible with the material being dispensed. This ensures a smooth fit into the pail as well as prevents curing type compounds from bonding to seal.

TO CHANGE DRUM:

NOTE: The needle valve knob should be turned clockwise to hold lift in the “UP” Position.

1.Unscrew thumb screw and remove old 5 gallon drum.

2.Place and center a new drum into position. Remove cover. Tighten thumb screw.

2 OF 4

NP322L-X

NP322L01-1 specifications

The Ingersoll-Rand NP322L01-1 is an industrial-grade air compressor that exemplifies advanced engineering and robust performance, catering to various applications in the construction, manufacturing, and automotive industries. Its design is centered around efficiency, reliability, and ease of use, making it a highly sought-after choice for professionals seeking optimal pneumatic power.

One of the standout features of the NP322L01-1 is its powerful engine, which offers a substantial horsepower rating, ensuring that it can handle demanding tasks with ease. This model utilizes a two-stage compression system, which enhances its overall efficiency significantly. By compressing the air in two stages, it achieves a higher output pressure with lower energy consumption compared to single-stage compressors.

Another key characteristic of the NP322L01-1 is its exceptional durability. It is built with high-quality materials designed to withstand harsh working environments. The robust construction ensures longevity, minimizing the need for frequent repairs or replacements, which translates to reduced operational costs for users.

The NP322L01-1 is equipped with innovative technologies that enhance its functionality. One such feature is the advanced control system, which allows for precise monitoring of pressure levels. This technology not only improves operational efficiency but also ensures the safety of both the equipment and the user. Additionally, the compressor boasts a built-in thermal overload protection mechanism, which prevents overheating and allows for prolonged use without the risk of damage.

Portability is another noteworthy aspect of the NP322L01-1. It is designed with mobility in mind, featuring rugged wheels and a compact frame that makes it easy to transport across job sites. This enhances its versatility, allowing it to be used in a variety of settings, from remote locations to busy workshop environments.

Moreover, the NP322L01-1 is engineered for easy maintenance. Its design allows for quick access to key components, facilitating routine maintenance procedures and reducing downtime. This ease of upkeep is essential for professionals who rely on consistent performance to meet tight deadlines.

In conclusion, the Ingersoll-Rand NP322L01-1 stands out as a top-tier air compressor that combines power, durability, and user-friendly features. Its advanced technologies ensure efficiency and safety, while its portable design allows for flexibility in various job environments. Whether for construction projects or industrial applications, the NP322L01-1 is a reliable choice that delivers outstanding performance and value.